DSC PowerSeries PC1616 Installation Guide

Chapter 5 Programming Worksheets
31
[005] System Times
For SIA CP-01 compliant installations, the Exit Delay must be within the range of 045-255 seconds (Default 60 seconds). If the Exit
Delay is silent (Section 14, Option 6 or Stay Function Key Arming), the exit delay must be twice the programmed value. It cannot, however,
exceed 255 seconds (i.e., 090-255 seconds).
For UL Installations, the Entry Delay plus the Communications Delay must not exceed 60 seconds.
Exit Time Restart shall be disabled when the panel is used in combination with T-Link TL250/TL300.
[007] Master Code
The master code can be restored to default in section [989] Default Master Code.
Section Zone Def. Section Zone Def. Section Zone Def. Section Zone Def.
[001]
01 01
I_____I_____I
[002]
17 00
I_____I_____I
[003]
33 00
I_____I_____I
[004]
49 00
I_____I_____I
02 03
I_____I_____I
18 00
I_____I_____I
34 00
I_____I_____I
50 00
I_____I_____I
03 03
I_____I_____I
19 00
I_____I_____I
35 00
I_____I_____I
51 00
I_____I_____I
04 03
I_____I_____I
20 00
I_____I_____I
36 00
I_____I_____I
52 00
I_____I_____I
05 04
I_____I_____I
21 00
I_____I_____I
37 00
I_____I_____I
53 00
I_____I_____I
06 04
I_____I_____I
22 00
I_____I_____I
38 00
I_____I_____I
54 00
I_____I_____I
07 04
I_____I_____I
23 00
I_____I_____I
39 00
I_____I_____I
55 00
I_____I_____I
08 04
I_____I_____I
24 00
I_____I_____I
40 00
I_____I_____I
56 00
I_____I_____I
09 00
I_____I_____I
25 00
I_____I_____I
41 00
I_____I_____I
57 00
I_____I_____I
10 00
I_____I_____I
26 00
I_____I_____I
42 00
I_____I_____I
58 00
I_____I_____I
11 00
I_____I_____I
27 00
I_____I_____I
43 00
I_____I_____I
59 00
I_____I_____I
12 00
I_____I_____I
28 00
I_____I_____I
44 00
I_____I_____I
60 00
I_____I_____I
13 00
I_____I_____I
29 00
I_____I_____I
45 00
I_____I_____I
61 00
I_____I_____I
14 00
I_____I_____I
30 00
I_____I_____I
46 00
I_____I_____I
62 00
I_____I_____I
15 00
I_____I_____I
31 00
I_____I_____I
47 00
I_____I_____I
63 00
I_____I_____I
16 00
I_____I_____I
32 00
I_____I_____I
48 00
I_____I_____I
64 00
I_____I_____I
Valid entries for Entry Delay are 030-255; valid entries for Exit Delay are 045-255 for SIA CP-01.
[01] Partition 1 Entry/Exit times [05] Partition 5 Entry/Exit times
030
I____I____I____I
Entry Delay 1
030
I____I____I____I
Entry Delay 1
045
I_0_I_3_I_0_I
Entry Delay 2
045
I_0_I_3_I_0_I
Entry Delay 2
120
I_0_I_6_I_0_I
Exit Delay
120
I_0_I_6_I_0_I
Exit Delay
[02] Partition 2 Entry/Exit times [06] Partition 6 Entry/Exit times
030
I____I____I____I
Entry Delay 1
030
I____I____I____I
Entry Delay 1
045
I_0_I_3_I_0_I
Entry Delay 2
045
I_0_I_3_I_0_I
Entry Delay 2
120
I_0_I_6_I_0_I
Exit Delay
120
I_0_I_6_I_0_I
Exit Delay
[03] Partition 3 Entry/Exit times [07] Partition 7 Entry/Exit times
030
I____I____I____I
Entry Delay 1
030
I____I____I____I
Entry Delay 1
045
I_0_I_3_I_0_I
Entry Delay 2
045
I_0_I_3_I_0_I
Entry Delay 2
120
I_0_I_6_I_0_I
Exit Delay
120
I_0_I_6_I_0_I
Exit Delay
[04] Partition 4 Entry/Exit times [08] Partition 8 Entry/Exit times
030
I____I____I____I
Entry Delay 1
030
I____I____I____I
Entry Delay 1
045
I_0_I_3_I_0_I
Entry Delay 2
045
I_0_I_3_I_0_I
Entry Delay 2
120
I_0_I_6_I_0_I
Exit Delay
120
I_0_I_6_I_0_I
Exit Delay
[09] Bell Cut-Off Timer (All Partitions)
004
I___I___I___I
Enter 3 digits from 001-255
[006] Installer’s Code [007] Master Code [008] Maintenance Code
Default Default Default
5555 I_______I_______I_______I_______I 1234I_______I_______I_______I_______I AAAAI_______I_______I_______I_______I

DSC PowerSeries PC1616 Specifications

General

Partitions	2
Keypads	Up to 8
Zones	6 on-board
PGMs	2
Power Supply	16.5VAC
Battery Backup	12VDC, 4Ah