To Next Page

To Previous Page

Safety

10 Service Instructions 171/173 - 00.0 - 01/2020

 This is what a warning looks like for a hazard that could result in envi-

ronmental damage if ignored.

 This is what a warning looks like for a hazard that could result in

property damage if ignored.

CAUTION

Type and source of danger!

Consequences of non-compliance.

Measures for avoiding the danger.

NOTICE

Type and source of danger!

Consequences of non-compliance.

Measures for avoiding the danger.

Default Chapter3
- Table of Contents3
1 About These Instructions5
- For Whom Are These Instructions Intended5
- Representation Conventions - Symbols and Characters5
- Other Documents6
- Liability7
2 Safety9
- Basic Safety Instructions9
- Signal Words and Symbols Used in Warnings10
3 Working Basis13
- Order of the Adjustments13
- Laying the Cables13
- Gage Set and Handwheel Positions14
- Gage Set14
- Handwheel Positions15
4 Adjusting the Adjusting Disk Relative to the Arm Shaft Crank17
5 Placing the Toothed Belt at the Bottom18
6 Position of Needle and Hook19
- Adjusting the Rocker Bolt for the Hook Drive and the Lower Shaft Bearing on the Left19
- Adjusting the Hook Drive Housing21
- Adjusting the Needle Evasive Movement (Ellipsis Width)22
- Adjusting the Symmetry of the Hook25
- Adjusting the Hook in the Hook Carrier26
- Adjusting Looping Stroke and Needle Bar Height27
- Adjusting the Needle Guard29
7 Feed Dog30
- Adjusting the Thrust Movement of the Feed Dog30
- Adjusting the Stroke Movement of the Feed Dog32
- Adjusting the Retention Spring on the Hook33
- Adjusting the Thread Take-Up Disk34
8 Adjusting the Thread Trimmer36
9 Adjusting the Sewing Foot Stroke42
- Adjusting the Sewing Foot Stroke for Presser Feet42
- Adjusting the Sewing Foot Stroke for Hinged Lever Feet45
10 Stitch Lengths47
- Adjusting Normal Stitch Lengths47
- Adjusting Stitch Condensing for the Bottom Feed48
- Adjusting Stitch Condensing for the Puller49
11 Puller50
- Adjusting the Synchronization of Bottom Feed and Puller50
- Adjusting the Distance between Carrier Roller and Needle51
- Adjusting the Lift Stroke of the Carrier Roller52
- Adjusting the Carrier Roller Pressure53
- Fabric Deflector54
- Toothed Belt Tension54
- Changing the Carrier Roller55
12 Edge Pinker56
- Disassembling the Edge Pinker56
- Changing the Knives57
- Adjusting the Cutting Pressure61
- Adjusting Point in Time for Cutting62
- Checking the Seam Pattern64
- Adjusting the Chain Cutter65
13 Programming67
- Adjusting the Electropneumatic Switching of the Carrier Roller71
- Adjusting the Stitch Count before the Carrier Roller Is Lowered71
- Adjusting Subclass 550-121 for Machines with an Edge Pinker72
14 Maintenance73
- Cleaning74
- Lubricating75
- Checking the Lubrication of the Machine Head76
- Checking the Hook Lubrication76
- Servicing the Pneumatic System77
- Adjusting the Operating Pressure77
- Draining the Water-Oil Mixture78
- Cleaning the Filter Element79
- Parts List80
15 Decommissioning81
16 Disposal83
17 Troubleshooting85
- Customer Service85
- Errors in Sewing Process85
18 Technical Data87
- Data and Characteristic Values88
- Requirements for Fault-Free Operation88
19 Appendix89

Brand	DURKOPP ADLER
Model	171
Category	Sewing Machine
Language	English

DURKOPP ADLER 171 Service Instructions

Table of Contents

Other manuals for DURKOPP ADLER 171

Questions and Answers:

DURKOPP ADLER 171 Specifications

Related product manuals