Emerson Branson LPX - Figure 1.1 Safety Label Found on the Back of the LPX Power Supply

88 pages

To Next Page

To Previous Page

100-412-196 REV. 06 3

1.1.2 Symbols Found on the Product

The LPX Power Supply has several warning labels on it to alert the user of items of concern

or hazard.

The following warning symbols appear on the LPX Power Supply.

Figure 1.1 Safety Label found on the back of the LPX Power Supply.

Main Page

Default Chapter5
- Table of Contents5
Chapter 1:Safety And Support11
Safety Requirements and Warnings12
- Figure 1.1 Safety Label Found on the Back of the LPX Power Supply13
General Precautions14
Chapter 5:Installation And Setup15
Chapter 6:Operation15
Regulatory Compliance16
Warranty Statement, Disclaimer17
- Table 1.1 Warranty Period17
How to Contact Branson19
Returning Equipment for Repair20
- Table 1.2 Branson Contacts22
Obtaining Replacement Parts23
Chapter 2:Introduction25
- Principle of Operation26
- Front Panel Controls and Indicators27
- Figure 2.2 Front-Panel Controls27
- Table 2.1 Front Panel Controls and Indicators28
- Table 2.2 LCD Icons30
- Back Panel Connections32
- Figure 2.3 Back Panel of LPX Power Supply32
- Table 2.3 Connections to the LPX Power Supply32
Chapter 3 3:Delivery and Handling34
Chapter 4 4:Technical Specifications36
- Table 4.1 Environmental Specifications36
- Table 4.2 Input Voltage36
- Table 4.3 Current Rating Fusing36
- Table 4.4 Maximum Power Limit37
- Table 4.5 Dimensions and Weight37
- Figure 4.1 Declaration of Conformity38
- System Performance Benchmark39
- Table 4.6 System Performance Benchmark39
- Branson Power Supply Setup Form40
Chapter 5:Installation And Setup41
Installation Checklist42
System Component Description43
- Figure 2.1 LPX Power Supply43
- Table 5.1 20 Khz LPX Power Supply Converter Compatibility43
- Table 5.2 30 Khz LPX Power Supply Converter Compatibility44
- Table 5.3 40 Khz LPX Power Supply Converter Compatibility44
- Table 5.4 LPX Power Supply Converter Part Numbers45
- Table 5.5 Start Cable Part Numbers45
- Table 5.6 RF Cable Part Numbers46
- Table 5.7 Handheld Welder Part Numbers46
- Table 5.8 Maximum Power/Duty Cycle47
Assembling the Equipment48
- Table 5.9 Setup Procedure48
- Table 5.10 Connecting the Horn to the Converter49
- Table 5.11 Stud Torque Values, Torque Wrench Part Numbers49
- Figure 5.1 Connecting Tip to Horn50
- Table 5.12 Connecting the Tip to the Horn50
Input Power Requirements51
Electrical Connections to Equipment52
- Table 5.13 User I/O Pin-Out (DB9F) Provided for Customer-Designed Interface53
Guards and Safety Equipment54
Chapter 6:Operation55
Front Panel Controls56
- Figure 6.1 LPX Power Supply User Interface56
System Modes57
- Table 6.1 System Modes and Description57
Main Screen Navigation58
System Configuration Registers60
- Table 6.2 Modify Registers60
- Table 6.3 Register Settings60
Operational Sequence63
- Table 6.4 Energy Mode Parameters63
- Table 6.5 Energy Mode Operational Sequence63
- Table 6.6 Time Mode Parameters67
- Table 6.7 Time Mode Operational Sequence67
- Table 6.8 Continuous Mode Parameters71
- Table 6.9 Continuous Mode Operational Sequence71
Save/Recall Weld Preset74
- Table 6.10 Saving a Weld Preset in Memory74
- Table 6.11 Recalling a Weld Preset from Memory75
Chapter 7:Maintenance77
Maintenance and Troubleshooting78
Reconditioning the Stack Interface80
- Figure 7.1 Reconditioning Stack Mating Surface80
Troubleshooting Charts83
- Figure 7.2 LPX Power Supply Interconnect Diagram85
Alarms/Errors86

Emerson Branson LPX - Figure 1.1 Safety Label Found on the Back of the LPX Power Supply

Table of Contents

Related product manuals