EndRun Sonoma D12 - Page 29

S o n o m a U s e r M a n u a l
12
C H A P T E R T W O
13
S o n o m a U s e r M a n u a l
B A S I C I N S T A L L A T I O N
If you are not using DHCP, the IP address shown should match the static IP address which you
entered during the netconfig procedure. If so, log in as “root” at the login prompt and check the
other conguration parameters using ifconfig:
Sonoma D12 CDMA(root@host:~)-> ifconfig
eth0 Link encap:Ethernet HWaddr 00:0e:fe:01:00:1c
inet addr:192.168.1.120 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:9694 errors:0 dropped:970 overruns:0 frame:0
TX packets:459 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:829805 (810.3 KiB) TX bytes:50242 (49.0 KiB)
Interrupt:11
eth1 Link encap:Ethernet HWaddr 00:0e:fe:01:00:1d
inet addr:192.168.5.1 Bcast:192.168.5.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:10143 errors:0 dropped:970 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:881081 (860.4 KiB) TX bytes:0 (0.0 B)
Interrupt:15
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:5808 errors:0 dropped:0 overruns:0 frame:0
TX packets:5808 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:728178 (711.1 KiB) TX bytes:728178 (711.1 KiB)
Pay particular attention to the settings shown for eth0 and eth1, in particular the Mask: setting,
which should match that which is appropriate for your network. Now check the remaining congura-
tion parameters using route:
Sonoma D12 CDMA(root@host:~)-> route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 192.168.1.1 0.0.0.0 UG 1 0 0 eth0
loopback * 255.0.0.0 U 0 0 0 lo
localnet * 255.255.255.0 U 0 0 0 eth0
192.168.5.0 * 255.255.255.0 U 0 0 0 eth1
Here you are interested in the default gateway address. It should match the appropriate one for your
network. If so, then the Ethernet interface of your Sonoma has been successfully congured to oper-
ate on your network and you are ready to check operation of the Sonoma over the network. If not,
you should recheck your conguration and/or repeat the netconfig procedure.
If you have congured a nameserver(s) for your network, you may check that by issuing this com-
mand:
Sonoma D12 CDMA(root@host:~)-> cat /etc/resolv.conf
search your.domain
nameserver 192.168.1.1
nameserver 192.168.1.2