EOGB X500 - Page 36

34
Revision 1 01/01/16
Spare parts list
Item Part number Description
1 E80-0901 Fan 120mm x 52mm le hand rotation
2 E80-0702 Motor mounting ange
3
M02-1-90-18 Motor
M02-0004 Capacitor 4mF
M02-0012 3 Pin motor lead
4 C01-0005 Motor/pump coupling
5
D01-071N0156 BFP11 L3 Pump Bio 10
D01-071N0010 BFP 240v coil
D01-071G0202 3 Pin pump solenoid cable 280mm
E80-300-202-204-02 Brass manifold 70mm 1/8”m x 1/8”m for
pressure gauge
E80-300-999-000-00 1/8” port plug
6 E80-1401 Outer oil pipe - Pump to nozzle assembly
7 E80-400-111-325-00 Bolt M6 x 24
8 E80-407-100-000-00 Spring
9a
E80-0404 Air intake housing X400 (narrow)
E80-0407 Air intake grill (narrow)
E80-501-001-000-04 Acoustic bae - X400 (narrow)
9b
E80-0405 Air intake housing X400/500 (balanced ue)
E80-0408 Air intake grill X400/500 (balanced)
E80-501-001-000-02 Acoustic bae X400/500 (balanced ue)
10a
E80-0010 Air damper (low output) + seal
10b E80-0007 Air damper (high output) + seal
11
E80-0401 Side cover X400
12
E80-500-005-120-00 Neoprene sponge sealing cord 650mm
required
13 E80-1302 Electronics cover X400
14 E80-302-006-112-01 5 pin terminal strip 32amp
15 E80-002-008-000-08 Control chassis X400
16 E80-1202 Inner assembly sliding bracket (xed) X400
17 S01-59101 Mounting ange for MZ photocell
18 E80-502-200-001-00 Grommet for inner assembly
19 S01-TF830.3 TF830.3 Control box
20 S01-70503 Cable entry plate for S98 base
21 S01-S98 S98 control box wiring base
22 X01-0048 Cable gland
23
D01-052F4031 EBI ignition transformer (includes mains
cable)
D01-052F0132 Mains lead for ignition unit 320mm
24 S01-MZ770S-2 MZ Photocell
25 E80-502-200-001-00 Grommet for ignition cables
26 E80-400-112-420-00 M8 x 20 steel zinc panhead slotted drive
27 E80-0203 Blast tube gasket 105 x 86 x 2mm
Item Part number Description
28
E80-0101 Blast tube type ETB 6-7-19-10 80mm
E80-0102 Blast tube type ETB 10-5-16-8 80mm X400
(standard)
E80-0103 Blast tube type ETB 10-5-16-8 127mm
E80-004-002-011-00 Blast tune type ETB 6-7-19-10 127mm
E80-0104 Blast tube type ETB 6-7-19-10 147mm
E80-0105 Blast tube type ETB 10-5-16-8 147mm
E80-004-002-031-00 Blast tube type ETB 6-7-19-10 207mm
E80-004-002-034-00 Blast tube ETB 10-5-16-8 207mm
29 E80-0202 O ring - Blast tube to burner mounting
ange 89mm ID x 5mm
30 E80-0701 Burner mounting ange
31 E80-0201 Burner mounting gasket
32 E80-402-102-080-00 M8 steel zinc plated half nut
33 E80-400-143-416-00 M8 x 16 steel zinc plated c/sunk
34 E80-0601 Ignition cable 3mm angled x 3mm straight
(sold individually)
35
E80-300-802-101-00 Inner assembly including nozzle holder to
suit X400 80mm head (Standard)
E80-300-802-103-00 Inner assembly including nozzle holder to
suit X400 127mm head
E80-300-802-105-00 Inner assembly including nozzle holder to
suit X400 207mm head
36 E80-1200 Electrode holder
37 E80-0301 Electrode block
38 Please note that the oil nozzle size should be determined by the
boiler/appliance manufacturer. If in doubt the please contact
EOGB for further information on nozzle sizing or refer to Table E
Page 21
10.1 X400 Spare parts list