Extraflame Comfort Maxi - Thermostat (as Per Standard); Language; User; Display

THE REMOTE CONTROL
20
LANGUAGE12.3.
It is possible to select the preferred language to display the various
messages.
Controls procedure
Press the
P5
key for 3 seconds. The SET CLOCK
SCROLLING TEXT WILL APPEAR.
Press the
P3
key
until LANGUAGE IS DISPLAYED. Press the
P5
key once
and select the language with the
P2
and
P3
keys. Con rm
the selection using the
P1
key. Press the same key several
times to exit the menu completely.
USER12.4.
The USER menu allows the  nal customer di erent stove
settings.
DISPLAY12.4.1.
This menu allows to regulate the brightness of the display.
Controls procedure
Press the
P5
key for 3 seconds. The SET CLOCK
SCROLLING TEXT WILL APPEAR. Press the
P3
key until
USER IS DISPLAYED. Press the
P5
key until DISPLAY is
shown and select the brightness of the display using the
P2
and
P3
keys. Con rm the selection using the
P1
key. Press
the same key several times to exit the menu completely.
PELLETS12.4.2.
The following menu allows the adjustment of pellet feed as a
percentage.
If the stove has functioning problems owing to the quantity of
pellets, adjust pellet feeding directly from the control board.
The problems correlated to the amount of fuel can be divided into
2 categories:
NO FUEL
the stove can never develop a suitable  ame, tending to 
remain very low even at high powers.
at minimum power the stove tends to almost switch-o 
taking the stove into “NO PELLETS” alarm condition.
when the stove displays the “ 
NO PELLETS” alarm, there
may be non-burned pellets inside the burn pot.
EXCESS FUEL:
the stove develops a very high  ame even at low power. 
the panoramic glass is very dirty, obscuring it almost totally. 
the burn pot tends to become encrusted, blocking the holes 
for air intake due to the excessive pellet feed, as it is only burned
partially.
If the problem occurs after only a few months
working, check that routine cleaning stated in the
stove booklet, has been carried out correctly.
The regulation to be performed is a percentage. Therefore a
modi cation of this parameter will lead to a proportional variation
of all stove feeding speeds.
Controls procedure
Press the
P5
key for 3 seconds. The SET CLOCK SCROLLING
TEXT WILL APPEAR.
Press the
P3
key until USER IS
DISPLAYED. Press the
P5
key until PELLET is displayed
and select the value using the
P2
and
P3
keys. Con rm the
selection using the
P1
key. Press the same key several times
to exit the menu completely.
Adjustment example
NO FUEL: Increase the percentage value by 5 points and try
the stove with the new calibration for at least half an hour.
If the problem is attenuated, but not solved, increase by
another 5 points. Repeat the operation until the problem is
solved. If the problem cannot be resolved, contact the after-
sales service.
EXCESS FUEL: Decrease the percentage value by 5 points
and try the stove with the new calibration for at least half an
hour. If the problem is attenuated, but not solved, decrease
by another 5 points. Repeat the operation until the problem
is solved. If the problem cannot be resolved, contact the
after-sales service.
STAND  BY12.4.3.
The Stby function is used if immediate stove switch-o is required
when temperature has been reached.
The STBY function can be set at ON or OFF using the procedure
that will be described.
In the factory the STBY function is always set at OFF (indicator
o )
STAND  BY WITH DIGITAL THERMOSTAT AS 12.4.3.1.
PER STANDARD
STBY FUNCTION SET AT ON
If the Stby function is activated (ON), if the stove reaches the
room temperature set, exceeding it by 2°C, it will switch-o after a
delay set in the factory, displaying STAND  BY.
When the room temperature is lower by 2°C than the set set,
the stove will start to work again at the power set on the display,
showing
WORK.