7373
NISEA
6.3 Messaggi
Codice
Fase Messaggio
Msg 001 Standby o avvio ciclo Serbatoio di carico vuoto
Msg 002 Standby o avvio ciclo Serbatoio di scarico pieno
Msg 003 Inserimento Pin Pin errato
Msg 004 Inserimento Pin Inserire Pin
Msg 005 Avvio Ciclo Porta aperta
Msg 006 Trasferimento dati su USB Trasferimento dati non riuscito
Msg 007
Termine positivo ciclo test valvola
sicurezza
Pressione di attivazione valvola sicurezza P=xxxkPa
Msg 008 Avvio Vuoto Test Temperatura di camera oltre il limite
Msg 009 Accensione macchina Serial number incongruenti fra CPU e MB
Msg 010 Accensione macchina Eseguire lubrificazione sistema motorizzato porta
Msg 011 Accensione macchina Sostituire filtro Bio-X
Msg 012 Accensione macchina Eseguire manutenzione
Pag.64
6.6 Risoluzione messaggi
Codice Fase Messaggio Possibile soluzione
Msg 001 Standby o avvio ciclo Serbatoio di carico vuoto Riempire il serbatoio di carico
Msg 002 Standby o avvio ciclo Serbatoio di scarico pieno Svuotare il serbatoio di scarico
Msg 003 Inserimento Pin Pin errato Introdurre il Pin corretto
Msg 004 Inserimento Pin Inserire Pin Inserire Pin
Msg 005 Avvio Ciclo Porta aperta Chiudere la porta
Msg 006 Trasferimento dati su USB Trasferimento dati non riuscito Verificare il supporto di memoria e ripetere l’operazione
Msg 007
Termine positivo ciclo test
valvola sicurezza
Pressione di attivazione valvola
sicurezza P=xxxkPa
-----
Msg 008 Avvio Vuoto Test
Temperatura di camera oltre il
limite
Ripetere il Vuoto test quando la temperatura di camera
rientra nel limite ammesso (45°C).
Msg 009 Accensione macchina
Serial number incongruenti fra
CPU e MB
Contattare il Servizio tecnico Faro
Msg 010 Accensione macchina
Eseguire lubrificazione sistema
motorizzato porta
Eseguire la lubrificazione del sistema motorizzato secondo le
istruzioni al par. 5.1.9 del manuale d’uso.
Msg001
Msg002
Msg003
Msg004
Msg005
Msg006
Msg007
Msg008
Msg009
Msg010
6.3 Messaggi
Codice
Fase Messaggio
Msg 001 Standby o avvio ciclo Serbatoio di carico vuoto
Msg 002 Standby o avvio ciclo Serbatoio di scarico pieno
Msg 003 Inserimento Pin Pin errato
Msg 004 Inserimento Pin Inserire Pin
Msg 005 Avvio Ciclo Porta aperta
Msg 006 Trasferimento dati su USB Trasferimento dati non riuscito
Msg 007
Termine positivo ciclo test valvola
sicurezza
Pressione di attivazione valvola sicurezza P=xxxkPa
Msg 008 Avvio Vuoto Test Temperatura di camera oltre il limite
Msg 009 Accensione macchina Serial number incongruenti fra CPU e MB
Msg 010 Accensione macchina Eseguire lubrificazione sistema motorizzato porta
Msg 011 Accensione macchina Sostituire filtro Bio-X
Msg 012 Accensione macchina Eseguire manutenzione
Pag.64
6.6 Risoluzione messaggi
Codice Fase Messaggio Possibile soluzione
Msg 001 Standby o avvio ciclo Serbatoio di carico vuoto Riempire il serbatoio di carico
Msg 002 Standby o avvio ciclo Serbatoio di scarico pieno Svuotare il serbatoio di scarico
Msg 003 Inserimento Pin Pin errato Introdurre il Pin corretto
Msg 004 Inserimento Pin Inserire Pin Inserire Pin
Msg 005 Avvio Ciclo Porta aperta Chiudere la porta
Msg 006 Trasferimento dati su USB Trasferimento dati non riuscito Verificare il supporto di memoria e ripetere l’operazione
Msg 007
Termine positivo ciclo test
valvola sicurezza
Pressione di attivazione valvola
sicurezza P=xxxkPa
-----
Msg 008 Avvio Vuoto Test
Temperatura di camera oltre il
limite
Ripetere il Vuoto test quando la temperatura di camera
rientra nel limite ammesso (45°C).
Msg 009 Accensione macchina
Serial number incongruenti fra
CPU e MB
Contattare il Servizio tecnico Faro
Msg 010 Accensione macchina
Eseguire lubrificazione sistema
motorizzato porta
Eseguire la lubrificazione del sistema motorizzato secondo le
istruzioni al par. 5.1.9 del manuale d’uso.
Msg011
Msg012
Sostuzione ltro BIO-X
Eseguire manutenzione
Code Possible cause Possible solution
AL 002 A blackout has occurred
Reset the machine.
Check:
a) that the power cable is connected correctly;
b) that there is mains power in the system;
Then repeat the selected program.
If the problem persists, contact technical support.
AL 003
There is a malfunction in the feed tank water filling
system.
Reset the machine.
Check that the water filling hose is positioned and connected
correctly, then repeat the selected procedure.
If the problem persists, contact technical support.
If water comes out of the overflow fitting at the rear, contact technical
support.
AL 100
There is a malfunction in the chamber probe reading
circuit
AL 101
There is a malfunction in the generator probe reading
circuit
AL 102
There is a malfunction in the pipe bundle probe reading
circuit
AL 103
There is a malfunction in the pressure transducer reading
circuit
AL 104
There is a malfunction in the door closing/opening
control system
AL 105
There is a malfunction in the door closing/opening
control system
AL 200 There is a malfunction in the temperature control system
AL 201 There is a malfunction in the temperature control system
AL 202 There is a malfunction in the temperature control system
Reset the machine.
Repeat the selected program.
If the problem persists, contact technical support.
Code Possible cause Possible solution
If the problem persists, contact technical support.
ER 160 There is a malfunction in the machine discharge system
Reset the machine.
Check the amount of load in the chamber and then repeat the selected
program.
If the problem persists, contact technical support.
ER 170 There is a malfunction in the machine drying system
ER 180 There is a malfunction in the pressure balancing system
Reset the machine.
Check the amount of load in the chamber and the Bio-X filter
condition, then repeat the selected program.
If the problem persists, contact technical support.
ER 200
There is a leak in the machine plumbing circuit or a
malfunction in the vacuum pump.
Reset the machine.
Check:
a) that the door seal is clean and positioned correctly;
b) that the filter in the chamber is clean and positioned correctly.
Then repeat the selected program.
If the problem persists, contact technical support.
ER 201 There is a leak in the machine plumbing circuit.
ER 202 There is a leak in the machine plumbing circuit.
Reset the machine.
Check that the door seal is clean and positioned correctly, then repeat
the selected program.
If the problem persists, contact technical support.
ER 203
A Vacuum Test is running in chamber conditions other
than ambient temperature.
Reset the machine.
Repeat the Vacuum Test, making sure that the chamber is at ambient
temperature.
If the problem persists, contact technical support.
ER 204 There is a malfunction in the pressure balancing system
Reset the machine.
Repeat the selected program.
If the problem persists, contact technical support.
AL 001 The reset button was pressed Reset the machine.
Code Possible cause Possible solution
AL 002 A blackout has occurred
Reset the machine.
Check:
a) that the power cable is connected correctly;
b) that there is mains power in the system;
Then repeat the selected program.
If the problem persists, contact technical support.
AL 003
There is a malfunction in the feed tank water filling
system.
Reset the machine.
Check that the water filling hose is positioned and connected
correctly, then repeat the selected procedure.
If the problem persists, contact technical support.
If water comes out of the overflow fitting at the rear, contact technical
support.
AL 100
There is a malfunction in the chamber probe reading
circuit
AL 101
There is a malfunction in the generator probe reading
circuit
AL 102
There is a malfunction in the pipe bundle probe reading
circuit
AL 103
There is a malfunction in the pressure transducer reading
circuit
AL 104
There is a malfunction in the door closing/opening
control system
AL 105
There is a malfunction in the door closing/opening
control system
AL 200 There is a malfunction in the temperature control system
AL 201 There is a malfunction in the temperature control system
AL 202 There is a malfunction in the temperature control system
Reset the machine.
Repeat the selected program.
If the problem persists, contact technical support.
Code Possible cause Possible solution
If the problem persists, contact technical support.
ER 160 There is a malfunction in the machine discharge system
Reset the machine.
Check the amount of load in the chamber and then repeat the selected
program.
If the problem persists, contact technical support.
ER 170 There is a malfunction in the machine drying system
ER 180 There is a malfunction in the pressure balancing system
Reset the machine.
Check the amount of load in the chamber and the Bio-X filter
condition, then repeat the selected program.
If the problem persists, contact technical support.
ER 200
There is a leak in the machine plumbing circuit or a
malfunction in the vacuum pump.
Reset the machine.
Check:
a) that the door seal is clean and positioned correctly;
b) that the filter in the chamber is clean and positioned correctly.
Then repeat the selected program.
If the problem persists, contact technical support.
ER 201 There is a leak in the machine plumbing circuit.
ER 202 There is a leak in the machine plumbing circuit.
Reset the machine.
Check that the door seal is clean and positioned correctly, then repeat
the selected program.
If the problem persists, contact technical support.
ER 203
A Vacuum Test is running in chamber conditions other
than ambient temperature.
Reset the machine.
Repeat the Vacuum Test, making sure that the chamber is at ambient
temperature.
If the problem persists, contact technical support.
ER 204 There is a malfunction in the pressure balancing system
Reset the machine.
Repeat the selected program.
If the problem persists, contact technical support.
AL 001 The reset button was pressed Reset the machine.
Code Possible cause Possible solution
If the problem persists, contact technical support.
ER 160 There is a malfunction in the machine discharge system
Reset the machine.
Check the amount of load in the chamber and then repeat the selected
program.
If the problem persists, contact technical support.
ER 170 There is a malfunction in the machine drying system
ER 180 There is a malfunction in the pressure balancing system
Reset the machine.
Check the amount of load in the chamber and the Bio-X filter
condition, then repeat the selected program.
If the problem persists, contact technical support.
ER 200
There is a leak in the machine plumbing circuit or a
malfunction in the vacuum pump.
Reset the machine.
Check:
a) that the door seal is clean and positioned correctly;
b) that the filter in the chamber is clean and positioned correctly.
Then repeat the selected program.
If the problem persists, contact technical support.
ER 201 There is a leak in the machine plumbing circuit.
ER 202 There is a leak in the machine plumbing circuit.
Reset the machine.
Check that the door seal is clean and positioned correctly, then repeat
the selected program.
If the problem persists, contact technical support.
ER 203
A Vacuum Test is running in chamber conditions other
than ambient temperature.
Reset the machine.
Repeat the Vacuum Test, making sure that the chamber is at ambient
temperature.
If the problem persists, contact technical support.
ER 204 There is a malfunction in the pressure balancing system
Reset the machine.
Repeat the selected program.
If the problem persists, contact technical support.
AL 001 The reset button was pressed Reset the machine.
Code Possible cause Possible solution
AL 203 There is a malfunction in the pressure control system
Reset the machine.
Contact technical support.
AL 300 There is a malfunction in the electronic system
AL 301 There is a malfunction in the electronic system
AL302
There is a malfunction in the electronic system
AL 303
There is a malfunction in the electronic system
AL 304
There is a malfunction in the electronic system
AL 305
There is a malfunction in the electronic system
AL 306
There is a malfunction in the electronic system
AL 307
There is a malfunction in the electronic system
AL 308
There is a malfunction in the electronic system
AL 309
There is a malfunction in the electronic system
AL 310
There is a malfunction in the electronic system
Reset the machine.
Repeat the selected program.
If the problem persists, contact technical support.
6.6 Message solutions
Code
Phase
Message
Possible solution
Standby or cycle start
Standby or cycle start
PIN entry
PIN entry
Cycle start
Data transfer to USB
Safety valve test cycle
successful
Vacuum Test Start
Machine switch-on
Machine switch-on
Machine switch-on
Machine switch-on
Feed tank empty
Feed tank full
Incorrect PIN
Enter PIN
Door open
Transfer not succssful
Safety valve activation pressure
P=xxx kPa
Chamber temperature over limit
Serial Number inconsistency
between CPU and MB
Lubricate the automated system
of the door
Replace the BIO-X lter
Conduct maintenance
Fill the feed tank
Empty the discharge tank
Enter the correct PIN
Enter PIN
Close the door
Check the memory device and repeat the operation
Repeat the Vacuum Test when the chamber temperature
returns below the allowed limit (45°)
Contact the Faro Technical Service
Lubricate the automated system according to the instructions
in par.5.1.9 of the user manual
Replace the BIO-X lter with original spare part Faro
Contact Faro Technical Service for routine mantenance
Code Possible cause Possible solution
AL 203 There is a malfunction in the pressure control system
Reset the machine.
Contact technical support.
AL 300 There is a malfunction in the electronic system
AL 301 There is a malfunction in the electronic system
AL302
There is a malfunction in the electronic system
AL 303
There is a malfunction in the electronic system
AL 304
There is a malfunction in the electronic system
AL 305
There is a malfunction in the electronic system
AL 306
There is a malfunction in the electronic system
AL 307
There is a malfunction in the electronic system
AL 308
There is a malfunction in the electronic system
AL 309
There is a malfunction in the electronic system
AL 310
There is a malfunction in the electronic system
Reset the machine.
Repeat the selected program.
If the problem persists, contact technical support.
AL 401 Generator malfunction
AL 402 Band malfunction
To Next Page
Loading...
