FEC HFC3000 - Page 47

Chapter 4 Installation
PAGE 4-15
UNUSED PIN No.: TB2-2, TB2-3 OUT-2~3
These are unused.
WORK OUTPUT 0 ~ 4: WORK SELECTION INPUT CHECK
The input signals, WORK SELECT 0 ~ 4, are returned as they are as the output signals, WORK
OUTPUT 0 ~ 4.
These are used to confirm matching with the work selection that is input.
WORK OUTPUT 4
PIN No.: TB2-6
WORK OUTPUT 3
PIN No.: TB3-8
WORK OUTPUT 2
PIN No.: TB3-7
WORK OUTPUT 1
PIN No.: TB2-5
WORK OUTPUT 0
PIN No.: TB2-4
WORK No.
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
1
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
ON
2
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
ON
OFF(OPEN)
3
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
ON
ON
4
OFF(OPEN)
OFF(OPEN)
ON
OFF(OPEN)
OFF(OPEN)
5
OFF(OPEN)
OFF(OPEN)
ON
OFF(OPEN)
ON
6
OFF(OPEN)
OFF(OPEN)
ON
ON
OFF(OPEN)
7
OFF(OPEN)
OFF(OPEN)
ON
ON
ON
8
OFF(OPEN)
ON
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
9
OFF(OPEN)
ON
OFF(OPEN)
OFF(OPEN)
ON
10
OFF(OPEN)
ON
OFF(OPEN)
ON
OFF(OPEN)
11
OFF(OPEN)
ON
OFF(OPEN)
ON
ON
12
OFF(OPEN)
ON
ON
OFF(OPEN)
OFF(OPEN)
13
OFF(OPEN)
ON
ON
OFF(OPEN)
ON
14
OFF(OPEN)
ON
ON
ON
OFF(OPEN)
15
OFF(OPEN)
ON
ON
ON
ON
16
ON
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
17
ON
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
ON
18
ON
OFF(OPEN)
OFF(OPEN)
ON
OFF(OPEN)
19
ON
OFF(OPEN)
OFF(OPEN)
ON
ON
20
ON
OFF(OPEN)
ON
OFF(OPEN)
OFF(OPEN)
21
ON
OFF(OPEN)
ON
OFF(OPEN)
ON
22
ON
OFF(OPEN)
ON
ON
OFF(OPEN)
23
ON
OFF(OPEN)
ON
ON
ON
24
ON
ON
OFF(OPEN)
OFF(OPEN)
OFF(OPEN)
25
ON
ON
OFF(OPEN)
OFF(OPEN)
ON
26
ON
ON
OFF(OPEN)
ON
OFF(OPEN)
27
ON
ON
OFF(OPEN)
ON
ON
28
ON
ON
ON
OFF(OPEN)
OFF(OPEN)
29
ON
ON
ON
OFF(OPEN)
ON
30
ON
ON
ON
ON
OFF(OPEN)
31
ON
ON
ON
ON
ON
32
WORK OUTPUT 5: WORK SELECTION INPUT CHECK PIN No.: TB2-1 OUT-1
This output signal is set to “ON” while a work among work Nos. 33 ~ 64 is selected.
Although the selection among the work Nos. 33 ~ 64 cannot be made using the [WORK SELECT]
input signals, WORK OUTPUT 5 can be used when a selection is made from the operation panel or
from a Fieldbus interface.
OUTPUT BANK [ON]