Fimap MxL Pro Series - Assembling the Squeegee Body; Inserting Water System Filter; Filling the Solution Tank with Water; Detergent Solution (Versions Without Fss)

ASSEMBLING THE SQUEEGEE BODY
For packaging reasons, the squeegee body comes disassembled from the machine. In order to mount it on the squeegee support, do the
following:
1. Make sure the machine is in a safe condition (read “MACHINE SAFETY”).
CAUTION: these operations must be carried out using protective gloves to avoid any possible contact with the edges or tips of metal
objects.
2. Unscrew the knobs (18) in the squeegee body pre-assembly (Fig.17).
3. First of all, insert the left-hand pin (19) on the squeegee body in the left slit (20) in the squeegee support (Fig.18), so that the bushing (21)
adheres to the walls of the slit.
4. Repeat the same operation for the right pin.
5. Tighten the knobs (18) to x the squeegee body to the support.
6. Insert the vacuum tube (22) into the sleeve (23) in the squeegee body (Fig.19).
N.B.: the tube must be positioned behind the squeegee lifting chain.
N.B.: Although the squeegee comes pre-adjusted, it is nevertheless recommended to read the section entitled “ADJUSTING THE
SQUEEGEE BODY RUBBER BLADES”.
INSERTING WATER SYSTEM FILTER
Before using the machine for the rst time the water system lter needs to be reset, for shipping reasons the lter cartridge and the cap have
been removed. To insert the lter cartridge in the water system lter body proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “SECURING THE MACHINE”).
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury to hands.
3. Insert the lter cartridge (24) in the housing on the cap (25) (Fig.20).
N.B.: The O-ring gasket in the lter cartridge should be inserted into its seat in the cap.
4. Go to the right-hand side of the machine and screw the cap (25) onto the body of the detergent solution lter (26) (Fig.21).
FILLING THE SOLUTION TANK WITH WATER
Before lling the solution tank, carry out the following steps:
1. Take the machine to the usual place for lling the solution tank.
2. Perform the procedure for securing the machine ( see the section titled “SECURING THE MACHINE”).
3. Check the solution tank drainage cap (27) (on the rear right-hand side of the machine) is tight. If this is not the case, turn it clockwise
(Fig.22).
4. Check the water system lter cap (25) (on the rear right-hand side of the machine) is tight. If this is not the case, turn it clockwise (Fig.21).
The solution tank can be lled with water in three di󰀨erent ways:
• Remove the cap-measuring device (28) (Fig. 23) and ll the solution tank by means of a rubber hose or a bucket.
• Using the ller hose (29) (Fig.24), which supports the water hose on its own, remember to remove the cap-measuring device (28) in order to
allow the air to vent properly.
• Using the optional automatic clean water rell system, connect the female connector on the tube to the male connector (30) on the machine
(Fig. 25); before connecting the tube, remember to remove the cap (31) and the cap-measuring device (28) to enable the air to be vented.
5. Fill with clean water, at a temperature not higher than 50°C and not lower than 10°C. The amount inside the tank can be seen by means of
the level tube (32) (Fig.26) on the rear of the machine.
DETERGENT SOLUTION (VERSIONS WITHOUT FSS)
After lling the solution tank with clean water add the liquid detergent to the tank in the concentration and manner indicated on the detergent
manufacturer's label. To prevent the formation of an excessive amount of foam that could damage the vacuum motor, use the minimum
percentage of detergent required.
CAUTION: protective gloves should always be worn before handling detergents or acidic or alkaline solutions, to avoid serious injury to the
hands.
CAUTION: Always use detergents which have a manufacturer's label that indicates that they are suitable for use with oor scrubbing
machines. Do not use acid or alkaline products or solvents without this indication.
ATTENTION: Acid or alkaline maintenance detergent tank be used with pH values between 4 and 10 and that do not contain: oxidising
agents, chlorine or bromine, formaldehyde, mineral solvents. The detergents used must be suitable for use with scrubbing machines.
16