Fort 280 Series User Manual

25
Safety devices:
-A special safety clutch that makes the machine
movements andworktooloperation possible by
means of a non-release lever positioned on the
handlebars(7Fig.1).Whenthisleverisreleased,
allthemachinefunctionsstopwithoutturningthe
engineoff.
-The clutch control lever has a special automatic
lockingsystemwhichpreventsaccidentalengage-
mentoftheclutch(twoactionsarenecessaryfor
engagingtheclutch:releaseusingthebutton(15
Fig.1)andactuationofthelever(7Fig.1).
Handlebars:adjustableinheightandlaterally.
Reversibleof180°.
Wheels:4.00x8-4.00x10-16x6.50x8
Wheel ination pressure:2.2bar.
Dimensions:Seegure2.
Speed:Thespeedvalueshavebeencalculatedwith
a3600rpmengine.
WHEELS CUTTER Forward km/h
1
a
2
a
3
a
 3,50x6 1,05 2,70 5,60
 4,00x8 1,30 3,32 6,85
 4,00x10 1,46 3,73 7,68
16x6,5x8 1,30 3,32 6,85
WHEELS CUTTER Reverse km/h
1
a
2
a
3
a
 3,50x6 0,87 2,27 4,56
 4,00x8 1,07 2,71 5,6
 4,00x10 1,20 3,04 6,28
16x6,5x8 1,07 2,71 5,6
N.B: In version cutter speeds are reversed.
Supplies: Refertotheenginebookletforthetypeof
fuelandchecktheidenticationdataontheplateon
theengineitself.
Thefueltankispartoftheengine.
SECTION 2
Safetyandprevention
2.1 SAFETY
Thepersonnelshallbeinstructedontherisksresult-
ingfromaccidentsonthedevicesarrangedforthe
operator’ssafetyandonthegeneralaccidentpreven-
tionregulationsprovidedforbythelegislationofthe
Countrywherethemachineisbeingused.
Whiledesigningthemachine,allthepotentialdanger-
oussituationswereforeseenandconsequentlythe
properprotectionswereadopted.Anyhow,thelevel
ofaccidentscausedbythecarelessandimproperuse
ofthemachineisstillhigh.
Thecarelessness,theirresponsibilityandthe too
muchfamiliarityaretoooftenthecauseofaccidents
aswellastirednessandsleepiness.
Youshallreadthismanualverycarefullyandinpartic-
ularthesectionconcerningthesafetyregulations.
DANGER
The Manufacturer shall not be held responsible for
the non-compliance with the safety and accident
prevention regulations provided for by the laws
and for the non-compliance with what is provided
for in this manual.
DANGER
Pay attention to this symbol in the instructions
manual.
It shows a possible hazard.
2.1.1 WORDS USED
Wordsofpeopleandofspecicsituationsthatmay
involvedirectlythemachinean/orthepersonsincon-
tactwiththemachineitselfareherebelowlisted.
• USER:Theuseristheperson,thebodyorthecom-
panywhohaspurchasedorrentedthemachineand
whointendstouseitforthedesignedpurposes.
Heshallberesponsibleforthemachineandforthe
trainingofallthoseworkingwithit.
• DANGEROUS AREA: Anyareawithinand/ornearthe
machinewherethepresenceofanexposedperson
impliesahazardforthesafetyandthehealthofthe
same.
• EXPOSED PERSON:Anypersonwhoiscompletely
orinpartnearadangerousarea.
• OPERATOR: Apersonwhoisabletooperate,to
carryoutthemaintenance,tocleanandtotransport
themachine.
• AUTHORIZED SERVICE CENTER:Theauthorized
servicecenteristhestructure legallyauthorized
bytheManufacturerthathasskilledpersonnelable
toperformalltheservice,maintenanceandrepair
ENGLISH

Fort 280 Series Specifications

General

Brand	Fort
Model	280 Series
Category	Tiller
Language	English