FSI DM160 - Page 11

© 2023 Flanders Scientic, Inc.
11
Return to Table of Contents
Scopes & Audio Meters 1, 2, 3
In addition to Real Time Scopes a wide variety of additional scopes and meters are available. Note that Real Time Scopes
are detected as active video on these scopes. These scopes and meters update approximately every 2 to 3 frames and
work in both Normal and Noise Reduction processing modes on DM series monitors. These functions toggle on/off a Scopes
& Audio Meters prole. Three prole slots are available from the Scopes & Audio Meters Menu and each prole can be
set to a specic function key allowing you to instantly toggle between various types of Scope and/or Audio Level Meter
congurations. Please note that if you have set both Scopes Windows to the Off position in the Scopes & Audio Meters
menu the luminance scope will appear when toggled.
Marker 1, 2, 3
These functions activate the on-screen display of the preset Area, Safety, Custom Graticules, or Active Boundary Markers
as set in the Marker Proles. Marker Proles can be customized via the Marker Menu. By utilizing this function you can
toggle on/off your selected markers with a single function key (see Marker Menu section of this manual for more details).
Fast Mode
Fast mode is an ultra-low-latency processing mode available on DM series monitors. Use this function to toggle Fast Mode
processing on and off. Please note that while Fast Mode is enabled menus and some ancillary functions will be locked out.
A list of Fast Mode compatible functions can be found below. Simply turn off Fast Mode to regain full access to all menus
and features.
For progressive and PsF signal formats there is only 1 type of low latency processing so Fast Mode can be toggled without
having to pre-congure any additional settings. For interlaced sources there are 4 available types of Fast Mode processing
that can be pre-congured from the Video Menu. See the Video Menu section of this manual for details on these processing
modes.
Function Menu
Available in DM Series Fast Mode
Real-time connection to LiveGrade Pro
Real-time connection to Prelight
Real-time connection to FirePlay and FireDay
Real-time connection to IP Remote Utility for Frame Capture,
ScopeStream, and Input Selection
Chroma/Bright/Contrast/Volume controls - controls are available,
but no OSD info
Real-time Scopes
3rd Generation Focus Assist
Marker 1, 2, 3
C-Log Standard and Full
S-Log Standard and Full
S-Log 2 Standard and Full
S-Log 3 Standard and Full
BMD-Log Standard and Full
Max Sharpness
DIT 3D LUT
3D Disparity
Image Flip
Custom Sharpness Level
Custom Graticules
All Color Space Selections
All Gamma Selections
All Color Temperature Selections
Color Matching Function Toggle
HDR Preview Modes
Custom Luminance Modes
LUT Bypass
RGB Gain/Bias Controls - Settings remain active, switch to
standard mode to adjust.
ACES Proxy v1.0.0
SDI Black Level Selection
Video Clipping Selection
Custom Gamma Selection
Keypad LED Selection
Black Detail Mode
Chroma/Bright/Contrast Lock and Unlock Selection
Available in Standard Mode Only
OSD Menu Access
Zoom, Pixel Zoom, DSLR Zoom
Red, Green, and Blue Only
Red, Green, and Blue Only as Mono
Overscan
Sub Window
Pixel Mapping
Mono Mode
Cross Hatch
H/V Delay
8 and 10 bit Pixel Picker Measurement Feature
CIE Measurement
LUM Coloring
SD Aspect Ratio
Full Screen Stretch Feature
Processed Scopes and Audio Meters 1,2,3 (*Note Real-time
Scopes do work in Fast Mode)
Variable Wipe
Still Frame
Safety Broadcast Mode
AFD Reader
Anamorphic De-squeeze
CX Scale
Rec. Status and On-screen Tally
Time Code Display
Video Data Analyzer
PAP Mode
CIE Scope
SD Enhancement
Part Display
Source ID
SDI Hue Adjustment