78
<Model Menu (Common Functions)>
$GMXVWPHQWUDQJHaVHF
(When the EDIT button is pushed for 1 second, the delay time
is reset to the initial value.)
3XVKWKH(',7EXWWRQWRHQGDGMXVWPHQWDQG
UHWXUQWRWKHFXUVROPRYHPRGH
WRWKHGDWDLQSXWPRGH
6HOHFWWKHIXQFWLRQE\WXUQLQJWKH(',7GLDO
DQGSXVKWKH(',7EXWWRQ
:KHQ\RXZDQWWROLQNWKLVPL[ZLWKRWKHU
PL[HVPRYHWKHFXUVRUWRWKH>/,1.@LWHPDQG
SXVKWKH(',7EXWWRQWRVZLWFKWRWKHGDWD
LQSXWPRGH
6HWWKHOLQNPRGHWR>@RU>@E\WXUQLQJWKH
(',7GLDODQGSXVKWKH(',7EXWWRQ
*Check the direction by actual operation.
Ɣ7ULPPRGH212))VHWWLQJ
:KHQFKDQJLQJWKHWULPPRGHPRYHWKH
FXUVRUWRWKH>75,0@LWHPDQGSXVKWKH(',7
EXWWRQWRVZLWFKWRWKHGDWDLQSXWPRGH
6HOHFW212))E\WXUQLQJWKH(',7GLDODQG
VHWWKHVHOHFWLRQE\SXVKLQJWKH(',7EXWWRQ
*When mixing includes master side trim, select [ON] and
when mixing does not include master trim, select [OFF].
*Effective when a function is set at the master channel.
Ɣ6ODYHFKDQQHO$)5PRGHVHWWLQJ67.67.
0RYHWKHFXUVRUWRWKH>67.67.@LWHP
VHOHFWWKHPRGHE\WXUQLQJWKH(',7GLDO
DQGFKDQJHWKHPRGHE\SXVKLQJWKH(',7
EXWWRQ
*When link is set at the slave side, and you want to add AFR
(D/R) to the mixing rate, select [ON].
*This is effective when the linkage is the same, but the travels
are substantially different.
Ɣ0L[LQJFXUYHVHWWLQJ
(For a description of the curve setting method, see the
description at the back of this manual.)
Ɣ)LQHWXQLQJWULPVHWWLQJ
Operation control [CTRL], operation mode
[MODE], and rate [RATE] adjustment is possible
by [FINE TUNING] item.
)RUDGHVFULSWLRQRIWKH¿QHWXQLQJWULPVHWWLQJPHWKRGVHH
the description at the back of this manual.)
Ɣ6HUYRVSHHGVHWWLQJ
Adjustment is possible with the [SPEED] item.
(For a description of the servo speed setting method, see the
description at the back of this manual).
Ɣ0L[LQJ212))GHOD\VHWWLQJ
Delay time at mix ON [START] and delay time
at mix OFF [STOP] adjustment is possible by
[DELAY] item.
*This function is inactive when a mixing switch is not set.
0RYHWKH>67$57@RU>6723@LWHPDQGSXVK
WKH(',7EXWWRQWRVZLWFKWRWKHGDWDLQSXW
PRGH
$GMXVWWKHGHOD\WLPHE\WXUQLQJWKH(',7GLDO
,QLWLDOYDOXHVHF