GE D30

xii D30 LINE DISTANCE PROTECTION SYSTEM – INSTRUCTION MANUAL
INDEX
RS232
baud rate ............................................................................................. 5-41
configuration ..................................................................................... 3-67
specifications ..................................................................................... 2-32
wiring ..................................................................................................... 3-32
RS422
configuration ..................................................................................... 3-43
timing .................................................................................................... 3-44
two-channel application .............................................................. 3-43
with fiber interface .......................................................................... 3-45
RS485
description .......................................................................................... 3-34
limitation with CyberSentry ......................................................... 5-16
port on rear panel ............................................................................ 3-12
settings ................................................................................................. 5-41
specifications ..................................................................................... 2-32
RTD FlexAnalogs .....................................................................................A-7
RTD inputs
actual values ...................................................................................... 6-21
settings ...............................................................................................5-316
specifications ..................................................................................... 2-29
Rules for passwords .............................................................................5-8
RxGOOSE
actual values ...................................................................................... 6-21
error messages ....................................................................................7-9
FlexAnalogs ...........................................................................................A-9
settings ................................................................................................. 5-70
S
Save settings ............................................................................................4-1
Saving setting does not take relay out of service ...............5-1
SCADA protocol selection .............................................................. 5-50
SCD file
import ..................................................................................................10-12
import preferences ......................................................................... 10-9
SCL compatible .................................................................................... 5-56
SCL file import ............................................................... 5-74, 5-76, 5-77
preferences ......................................................................................... 10-9
Second Ethernet Fail ......................................................................... 5-37
Security
commands .............................................................................................7-4
delete files and records ...............................................................10-29
EnerVista and UR secure with SSH .............................................2-4
failed authentication lockout ..................................................... 5-21
forceful user logout ............................................................................7-3
lock FlexLogic equations .................................................................4-9
password for settings template ...................................................4-7
passwords for settings and commands ..........4-59, 5-9, 5-10
RADIUS server for user authentication .....................................B-1
role-based user access ....................................................................2-5
settings ................................................................................................. 5-19
software options .............................................................................. 2-35
specifications ..................................................................................... 2-35
system and event logs .................................................................. 5-24
Security audit list of port numbers ........................................... 5-44
Selector switch
actual values .........................................................................................6-7
application example .................................................................... 5-267
FlexLogic operands ...................................................................... 5-171
logic diagram .................................................................................. 5-269
settings ............................................................................................... 5-262
specifications .....................................................................................2-26
timing .................................................................................................. 5-266
Self-tests
description ..............................................................................................7-6
error messages ....................................................................................7-6
FlexLogic operands ...................................................................... 5-175
user-programmable .................................................................... 5-122
Serial number ...................................................................3-1, 4-11, 6-27
Serial ports
settings ..................................................................................................5-41
specifications .....................................................................................2-32
Series-compensated lines ..............................................................9-18
Server authentication .......................................................................5-15
Server unavailable self-test ..........................................................7-11
Service life expected .........................................................................10-3
Service Report ..........................................................................................1-2
Setting groups .......................................................5-188, 5-189, 5-261
active setting group ..................................................................... 5-188
FlexLogic operands ...................................................................... 5-172
troubleshooting .............................................................................. 5-189
Setting lock self-test ..........................................................................7-11
Settings ........................................................................................................5-1
back up ..................................................................................... 5-58, 10-8
change .................................................................................................. 4-52
change does not take relay out of service ..............................5-1
compare ...............................................................................................10-7
control user accounts ....................................................................5-13
convert ..................................................................................................10-5
edit ..........................................................................................................4-52
export .....................................................................................................10-8
import ....................................................................................................3-70
not updated automatically among computers ................. 3-66
read from device with Modbus Analyzer ..............................10-1
restore ...................................................................................................10-8
upgrade ................................................................................................10-5
write to device with Modbus Analyzer ...................................10-1
Settings file ..............................................................................................5-58
description ..............................................................................................4-1
import ....................................................................................................3-70
takes relay out of service when loaded ....................................4-2
traceability ...........................................................................................4-12
transfer with USB stick ...................................................................4-16
Settings password .........................................................4-59, 5-9, 5-10
Settings templates
description ..............................................................................................4-5
edit .............................................................................................................4-6
enable .......................................................................................................4-5
password protection .........................................................................4-7
remove .....................................................................................................4-9
view ............................................................................................................4-7