GE MOTOR MANAGER 2 - Page 218

ii
MM2 Motor Manager 2
GE Power Management
INDEX
G
GE OVERLOAD CURVES
.......................................4-9
GE POWER MANAGEMENT WARRANTY
.............G-2
GROUND CURRENT
...............................................5-3
GROUND FAULT ALARM
.......................................4-13
GROUND FAULT CT
................................................2-5
GROUND FAULT CT INPUT
...................................4-5
GROUND FAULT CURRENT FUNCTIONS
............7-5
GROUND FAULT TRIP
...........................................4-14
GROUND SURGE
....................................................2-5
GROUNDING
phase and ground CTs
..........................................C-1
H
HARDWARE REVISION
..........................................4-34
HIGH SPEED START BLOCK
.................................4-4
HI-POT TESTING
.....................................................2-8
HOT/COLD CURVE RATIO
....................................4-12
I
INPUT FUNCTIONS
.................................................7-5
INPUTS
analog
.....................................................................C-2
stop switch
..............................................................C-2
switch
......................................................................C-2
thermistor
................................................................C-2
INSTALLATION
........................................................2-1
INTERLOCK COUNTER
clearing
...................................................................4-7
INTERLOCK INPUTS 1-10
.....................................4-20
INTERNAL FAULT TRIP
..........................................4-6
INVERTER STARTER
....................................9-17, 9-19
L
LAST STARTING CURRENT
...................................5-4
LOAD INCREASE ALARM
......................................4-17
LOCAL ISOLATOR
...........................................2-8, 4-20
M
MAXIMUM MOTOR STOPPED TIME
.....................4-32
MEMORY MAP
...............................................6-19, 6-20
MINIMIZE RESET TIME
..........................................4-15
MM2PC
communications
....................................................8-13
configuring
..............................................................8-4
setpoints
.........................................................8-9, 8-10
MOD NUMBER
........................................................4-34
MODBUS
...................................................................1-1
data formats
..........................................................6-41
function code 01
.....................................................6-5
function code 03
.....................................................6-6
function code 04
.....................................................6-7
function code 05
.....................................................6-8
function code 06
.....................................................6-9
function code 07
...................................................6-10
function code 08
...................................................6-11
function code 10
...................................................6-12
memory map
..........................................................6-19
supported functions
................................................6-4
MODEL NUMBERS
...................................................1-2
MOTOR GREASING INTERVAL
............................4-32
MOTOR LOAD
...........................................................5-3
MOTOR NAME
..........................................................4-3
MOTOR RATING
.......................................................4-3
MOTOR START THREE PHASE CURRENT
..........D-2
MOTOR STATUS
......................................................5-3
N
NOMINAL FREQUENCY
...........................................4-5
O
OPEN CONTROL CIRCUIT TRIP
..........................4-16
OPTIONS
...................................................................1-1
ORDER CODES
........................................................1-2
ORDER INFORMATION
.........................................4-34
OUTPUT RELAYS
.....................................................2-6
OVERLOAD CURVE NUMBER
..............................4-12
OVERLOAD CURVES
GE Power Management
..........................................4-9
setpoints
................................................................4-12
OVERLOAD PICKUP LEVEL
..................................4-12
OVERLOAD TRIP RESET
......................................4-16
P
PARITY
.............................................................4-3, 8-13
PART WINDING STARTER
....................................9-28
PHASE CT INPUTS
..................................................2-5
PHASE CT PRIMARY AMPS
....................................4-5
PHASE CURRENT FUNCTIONS
.............................7-3
PHASE CURRENTS
..................................................5-3
PHASE UNBALANCE
................................................5-4
PHASE UNBALANCE ALARM
................................4-16
POWER FAIL TEST
..................................................7-6
PRIMARY INJECTION TESTING
.............................7-1
PRIMARY RESISTANCE STARTER
.............9-14, 9-16
PROCESS STOP
.....................................................4-25
PROGRAMMABLE SWITCH INPUTS
......................2-6
Q
QUESTIONS AND ANSWERS
................................B-1