GE PACE5000 - Restore as Shipped Settings; Language Setting

98 pages

To Next Page

To Previous Page

PACE Pressure Controller User Manual

[EN] English 6 - 23 K0443 Revision A

Figure 1 Language Setting

Restore as shipped settings

Restores instrument settings to factory default, but does not affect PIN settings.

Main Page

Introduction2
Safety2
Pressure2
Maintenance2
Environmental Conditions3
Abbreviations3
Related Publications4
Symbols4
Warnings5
Pressure Units and Conversion Factors6
Unit Conversion6
Table of Contents7
Description10
- PACE5000 General View10
- PACE6000 General View10
Introduction10
- PACE5000 Rear View11
- PACE6000 Rear View11
- Packaging for Storage or Transportation12
- Packaging List12
Installation12
Preparation for Use12
PACE Pressure Port13
Pneumatic Connections13
- Pressure Module Rear View15
- Supply Equipment16
- Pneumatic Connection Examples16
- , Pneumatic Connections Without Vacuum Supply16
- Pneumatic Connections with Negative Gauge Pressure Generator18
- General19
Rack-Mount Option19
Electrical Connections20
- Pressure Control Module Input and Output Connectors21
- 4-Way Connector:21
- Communication Connections22
- RS232 Interface23
- Handshaking Connections23
- IEEE 488 Interface24
- Single Unit Installation24
- Multiple Unit Installation24
- IEEE 488 Connection25
Operation26
Preparation26
Touch Screen Areas27
Power-Up Sequence27
Display Icons28
Measure Mode28
- Measure Set-Up29
- Controller off – Decreasing Set-Point30
- Controller on – Increasing Set-Point30
- Controller off – Increasing Set-Point30
- Auto-Range30
- Control Mode31
- Controlling to a New Set-Point32
- Effort Meter33
- Controlling to Ambient/Zero Pressure33
Control Mode34
Operation and Example Procedures35
- Task36
- Divider37
- Divider Menu Structure37
- Preset38
Global Set-Up Selections39
Status Area Settings40
Barometric Reference Option40
Supervisor Set-Up41
Instrument Status42
- Software43
- Maintenance Tasks44
Cleaning44
Test44
Calibration44
Introduction44
Visual Inspection44
Calibration45
Replacement Parts45
Fuse Replacement45
Pressure Module Filters47
Filter Replacement47
Pressure Module Replacement48
Testing and Fault Finding50
Introduction50
Standard Serviceability Test50
Fault Diagnosis52
Fault Finding52
Approved Service Agents52
- Gas Supply54
- Supply Conditioning Equipment54
Reference and Specification54
Installation Notes54
- Vacuum Pump55
- Operating Near Atmospheric Pressure or below55
- Systems Without a Negative Supply55
- Supply Contamination55
- Air Density Values56
- Oil Contamination57
- Pump Performance57
Operational Requirements57
- Venting58
- Vent58
- Zero58
- Output Port58
- Display Icons in Set-Up Menus59
Icons59
- Pressure Zero62
- Units62
Measure Set-Up62
- Nudge63
- Slew Rate63
- Passive Control63
Control Set-Up63
Global Set-Up64
Supervisor Set-Up64
- Ethernet Firewall67
- Ethernet Parameters Range Setup67
- To Reset the LAN Settings72
- To Turn the LAN Status Indicator on or off72
- Usb73
- Timeout73
- Idle Timeout74
- Gas Head Correction74
- Power up74
- Lock Tasks74
- Language75
- Adding a Language75
- Restore as Shipped Settings76
- Language Setting76
- Option Enable Process77
- Options in the Task Menu77
- Leak Test Option77
Options77
- End79
- Example Switch Test Connections79
- Start79
- Switch Test Option79
- Test Program Option80
- To Start a Test Program81
- To Write a Test Program81
- To Edit an Existing Program81
- To Enter a Name for the Program81
- Test Program Commands82
- Example Program83
- Programming Loops84
- Example of Programming a Loop84
- Aeronautical Testing86
- Aeronautical Option86
- Leak Testing86
- Example of Altitude and Airspeed Testing87
- Reference Pressure88
- Go to Ground88
- Control of Aeronautical Parameters89
- Screen Layout90
- Measurement Mode90
- Set-Points91
- 15-Way Female D Connector92
- Analogue Output Option92
- Volts-Free Contact Option93
Calibration94
6.10 Communications - Instrument Emulation94
6.11 Specification94
6.12 Return Goods/Material Procedure94
- Safety Precautions95
- Environment95
6.13 Packaging Procedure95
Vacuum System Parts96

GE PACE5000 - Restore as Shipped Settings; Language Setting

Table of Contents

Other manuals for GE PACE5000

Related product manuals