GMI GT series - Page 122

147 pages

To Next Page

To Previous Page

13-20

OPERATOR MAINTENANCEUSER HANDBOOK

PROBE LOCATION

SECURING STRAP

POWER ON INDICATOR

Fig. 13.18 GT Series Charging Station

Main Page

Default Chapter3
- Copyright3
- Liability3
- Modification Notices3
- Software3
- Disposal Advice3
- Safety4
- Special Conditions for Safe Use5
- Areas of Use5
- Storage, Handling and Transit5
- Warranty5
- Table of Contents7
Introduction13
- Instrument Ranges14
General Features17
- Modes of Operation18
Operating Procedure19
- Switch the Instrument on20
- Instrument Identification20
- Battery Status21
- Filter Check / Flow Fault Test21
- Time and Date22
- Calibration Due Date22
- Service Due Date26
- Sensors Zeroing29
- Switch the Instrument off or Re-Enter the Mode Menu30
Leak Test Mode33
- Leak Test Ranges33
- Leak Test Features33
- Leak Test Displays34
- Leak Test Button Operation37
- Description of Leak Test Button Operation37
- Leak Test Ticker (Geiger) Function41
- Leak Test Alarms42
- Leak Test Logging42
Confined Space Mode43
- Csm Ranges43
- Csm Features43
- Csm Displays44
- Csm Button Operation45
- Description of Csm Button Operation46
- Csm Pump48
- Csm Alarms48
- Csm Logging48
- Csm Confidence Signal49
Barhole Testing Mode51
- Barhole Ranges51
- Barhole Features51
- Barhole Displays52
- View Barhole Results57
- Barhole Operation58
- Description of Barhole Button Operation58
- Barhole Alarms60
Co (Carbon Monoxide) Mode61
- Co Ranges61
- Co Features61
- Co Menu61
- Co Displays62
- Co Button Operation66
- Description of Co Button Operation66
- Co Alarms68
- Co Logging68
Purge Mode69
- Purge Ranges69
- Purge Features69
- Purge Displays69
- Purge Button Operation70
- Description of Purge Button Operation71
- Purge Alarms72
Sniffer Mode73
- Sniffer Ranges73
- Sniffer Features73
- Sniffer Displays74
- Sniffer Button Operation75
- Description of Sniffer Button Operation75
- Sniffer Ticker (Geiger) Indication77
Pressure Mode79
- Pressure Ranges79
- Pressure Features79
- Pressure Displays79
- Prepare Instrument (Pressure Mode)80
- Pressure Button Operation81
- Description of Pressure Button Operation81
- Pressure Alarms82
Bump Test Mode83
- Bump Test Ranges83
- Bump Test Features83
- Bump Test Displays84
- Bump Test Button Operation87
- Bump Test Logging88
Alarms89
- Gas Alarms89
- Flammable (Lel) Alarms89
- Oxygen (O ) Alarms89
- TOXIC GAS (E.g. CO) ALARMS89
- Alarm Types94
- Fault Alarms97
Operator Maintenance103
- Cleaning103
- Filter Replacement103
- Dust Filter104
- Hydrophobic Filter105
- Chemical Filter (Accessory)107
- Cotton Filter (Accessory)112
- Battery Replacement114
- Remove and Replace Batteries115
- Charging (Rechargeable) Batteries119
Calibration127
- Calibration Validity128
Accessories129
Additional Information131
- Training131
- World Wide Web131
Typical Operating Parameters133
- Dimensions (Excluding Probe134
- Weight (Including Probe & Batteries134
- Temperature Limits134
- Humidity134
- Construction / Protection Rating134
- Display134
- Sampling System134
- Power Source134
Quick Operating Instructions135
Index143

GMI GT series - Page 122

Table of Contents

Other manuals for GMI GT series

Related product manuals