Graco GM 5000 User Manual (English)

Other manuals for Graco GM 5000

Questions and Answers:

H
hollowaycurtisAug 20, 2025
How to fix a Graco GM 5000 when the engine won't start?
- V
  Valerie FerrellAug 21, 2025
  If your Graco Paint Sprayer's engine won't start, several issues could be the cause. First, ensure the engine switch is turned on. Check if you're out of gas and replenish if necessary. Also, verify the engine oil level; if the light on the rear of the engine is on, add oil. Inspect the spark plug cable to ensure it's connected, and replace the spark plug if it's damaged. If water is frozen in the pressure control, return it to an authorized Graco dealer for repair.
T
Terri PerryAug 22, 2025
Why is my Graco Paint Sprayer gun spitting?
- S
  Sherri LewisAug 22, 2025
  If you notice spitting from the gun of your Graco Paint Sprayer, it could be due to a few reasons. First, check for air in the fluid pump or hose, tighten any loose connections at the pump intake, and then prime the pump. Also, check if the tip is partially clogged and clear it. Lastly, ensure your fluid supply isn't low or empty; refill and prime the pump, checking the fluid supply frequently to prevent the pump from running dry.
K
Katie SimonAug 25, 2025
How to prime a Graco Paint Sprayer when it's difficult?
- B
  Brooke WilcoxAug 25, 2025
  If you are finding that the pump on your Graco Paint Sprayer is difficult to prime, consider the following: * Check all hose connections for air leaks and tighten as needed. Reduce RPM and cycle pump as slowly as possible during priming. * If the intake valve is leaking, shut off the pump, relieve pressure, and then disassemble and clean the intake valve, ensuring the ball seat is in good condition. Reassemble. * Consider repacking the pump if the packings are worn. * If the fluid is too thick, thin it according to the supplier’s recommendations.
D
douglasburtonAug 26, 2025
Why won't my Graco Paint Sprayer engine start?
- J
  Joe ConradAug 26, 2025
  Your Graco Paint Sprayer might not start for several reasons: * The engine switch might not be turned on; ensure it is. * The sprayer may be out of gas; replenish the gas. * The engine oil level could be low; try starting the engine and, if the light on the rear of the engine glows, add more oil. * The spark plug cable might be disconnected, or the spark plug could be damaged; connect the cable or replace the spark plug. * Water may be frozen in the pressure control; in this case, return the pressure control to an authorized Graco dealer for repair.
C
chadkochAug 28, 2025
What to do if Graco GM 5000 is spitting from the gun?
- T
  thompsonjoshuaAug 28, 2025
  If your Graco Paint Sprayer is spitting, it could be due to: * Air in the fluid pump or hose: Check for loose connections at the pump intake and tighten them, then prime the pump. * A partially clogged tip: Clear the tip. * Low or empty fluid supply: Refill and prime the pump. Check the fluid supply often to prevent running the pump dry.
I
isaacholmesAug 29, 2025
What to do if paint leaks into the wet-cup of my Graco GM 5000 Paint Sprayer?
- M
  Marissa WoodAug 29, 2025
  If paint is leaking into the wet-cup of your Graco Paint Sprayer: * The wet-cup may be loose; tighten it just enough to stop the leakage. * The throat packings may be worn or damaged; replace the packings. * The displacement rod may be worn or damaged; replace the rod.
C
Cheryl RhodesAug 31, 2025
Why is my Graco Paint Sprayer pump difficult to prime?
- M
  michellerobertsSep 1, 2025
  If you're having trouble priming your Graco Paint Sprayer pump: * There may be an air leak; check all hose connections and tighten as needed. Reduce RPM and cycle the pump as slowly as possible during priming. * The intake valve may be leaking; shut off the pump and relieve pressure. Disassemble and clean the intake valve, ensuring the ball seat is not nicked or worn and that the ball seats well. Then, reassemble. * The packings may be worn; repack the pump. * The fluid may be too thick; thin the fluid according to the supplier’s recommendations.
L
lynn28Sep 2, 2025
Why is the fluid delivery low on my Graco GM 5000 Paint Sprayer?
- M
  Manuel SellersSep 2, 2025
  If you're experiencing low fluid delivery with your Graco Paint Sprayer, start by checking the pump inlet screen for clogs and clean it if necessary. Ensure the pressure setting isn't too low and increase it if needed. Also, verify that the engine RPM isn't too low and increase the throttle setting. Check for any blockages in the outlet filter, tip filter, or tip, and clean them. Finally, consider if there's a large pressure drop in the hose; if so, switch to a larger diameter hose.
G
Garrett ParksSep 4, 2025
What causes low displacement pump output on my Graco GM 5000 Paint Sprayer?
- B
  Brian CraigSep 4, 2025
  If the displacement pump output is low on the downstroke, or both strokes, of your Graco Paint Sprayer, there are several possible causes. Begin by checking the pump inlet screen for clogs and clean it if necessary. If the piston packings are worn or damaged, replace them. Additionally, examine the intake valve ball check to ensure it is seating properly; clean and service it as needed. Verify that the engine RPM is not too low, and increase the throttle setting if required. Finally, a worn or damaged clutch could also be the culprit, in which case it should be replaced.
J
Jeffrey StevensSep 6, 2025
How to stop paint from leaking into the wet-cup of my Graco Paint Sprayer?
- M
  Matthew JohnsonSep 6, 2025
  If paint is leaking into the wet-cup of your Graco Paint Sprayer, the issue could stem from a few sources. First, check if the wet-cup is loose and tighten it just enough to stop the leakage. If the throat packings are worn or damaged, they will need to be replaced. Lastly, examine the displacement rod for any wear or damage, and replace the rod if necessary.