GRAPHTEC CE6000-40 Plus - User Manual

CE6000-UM-251-13-9370
C E 6000 Series
SERVICE MANUAL
MANUAL NO. CE6000-UM-251
CUTTING PLOTTER

GRAPHTEC CE6000-40 Plus Specifications

General

Model	CE6000-40 PLUS
Programmable Resolution (HP-GL)	0.025 mm
Repeatability Precision	±0.1 mm
Connectivity	USB, Serial
Command Sets	GP-GL, HP-GL
Interfaces	USB
Media Types	Vinyl, film
Media Thickness (Max)	0.25 mm
Power Supply	AC 100-240V, 50/60Hz
Operating Environment	Humidity: 35 to 75 % R.H. (non-condensing)
Compatible OS	Windows
Cutting Force	30 - 350 gf
Cutting Force Range	30 - 350 gf

Summary

1 INTRODUCTION

1.1 Main Specifications

Details the technical specifications for different CE6000 models.

2 PARTS NAMES and FUNCTIONS

2.1 Parts Names and Functions (CE6000-40;60;120;120 AMO)

Identifies and explains the parts of CE6000-40/60/120/120AMO models.

2.2 Assembling the Stand (CE6000-40;60;120;120 AMO)

2.3 Parts Names and Functions (CE6000-120 AP)

Identifies and explains the parts of the CE6000-120AP model.

2.4 Assembling the Stand (CE6000-120 AP)

3 OPERATIONS

3.1 Control Panel

Explains the function of buttons and lamps on the control panel.

6 DISASSEMBLY AND REASSEMBLY

6.1 Exterior Parts

6.2 Mechanical Parts

Covers disassembly and reassembly of internal mechanical components.

7 ELECTRICAL ADJUSTMENTS

7.1 DIP Switch Settings

Explains DIP switch configurations for different models.

7.2 List of Items Requiring Readjustment

Identifies components needing readjustment after replacement or alteration.

7.3 Explanation of the Values of the Main Board Settings

7.4 Clearing the Non-Volatile RAM

Procedure for clearing NV-RAM after main board replacement.

7.6 The Suffix setting

7.7 Adjusting the Pen Force

Procedure for adjusting pen force for different pen types.

7.8 Adjusting the Distance Accuracy

Steps for calibrating the plotter's distance accuracy.

7.9 Adjusting the Registration Mark Sensor Sensitivity

Process for adjusting the sensitivity of the registration mark sensor.

7.10 Adjusting the Offset of the Registration Mark Sensor

Calibrating the offset for the registration mark sensor and tool position.

7.11 Adjusting the RMS sensor and the Paper sensor position

Adjusting the position of RMS and paper sensors for accurate media detection.

7.12 Adjusting the Tool Exchange Position (CE6000-120 AP)

Setting the tool exchange position for the 2nd tool on CE6000-120AP.

7.13 Adjusting the Offset between Tool 1 and Tool 2 (CE6000-120 AP)

Calibrating the positional offset between tool 1 and tool 2.

7.14 Adjusting the Y Limit Position (CE6000-120 AP)

7.15 Upgrading the System Firmware

Instructions for updating the plotter's system firmware.

8 SERVICE MODES

8.1 Sensor and Key switch test Mode

8.2 Clear Setup Mode

8.6 Self Diagnostic Test

9 TROUBLESHOOTING

9.1 The Plotter is Turned On But Doesn’t Operate

Addresses issues where the plotter does not power on or function.

9.2 Media Loading Operations

9.3 Cutting Operations

9.4 Error Messages in GP-GL Command Mode

Explains error codes and solutions for GP-GL commands.

9.5 Error Messages in HP-GL Command Mode

Explains error codes and solutions for HP-GL commands.

9.6 ARMS Error Messages

Troubleshooting steps for Automatic Registration Mark System errors.

9.7 Other Error Messages

9.9 Troubleshooting of experience

11 BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS

11.1 Block Diagrams

11.2 Circuit Diagrams