TRX-VI-33100 Module
Planning and Installation Manual 203
Figure 119. Vertical blanking interval menu for NTSC, showing setup for all 16 inputs. PAL
display is similar. (Only Input 0 is connected in this example.).
Vertical Blanking Interval (VBI) -
--------------------------------------------------------------------------------
Reference - Input 0: Line Rate: 525 Line Type: NTSC (M, J)
================================================================================
Disable (Off) 0 NTSC-Reserve Data: VBI:
Enable (On) 1 None 0 None 0
21/284 1 Blank Line Only 1
Notch Decode: 22/285 2 Add Setup Only 2
Notch Decode 1 23/286 3 Setup & Blank 3
Pass Through 2 24/287 4
--------------------------------------------------------------------------------
+------------- Channel Line Rate --------+
| +----------- Notch Decode Mode |
| | +--------- Chroma Kill (On/Off) |
| | | +------- Reserve Line for Data Mode |
| | | | |
| | | | |<-------- VBI Line Pairs ------>|<- Data ->| |
| | | | | | | |
| | | | |E F G H I J K L M N O |P Q R S | |
| | | | |10 11 12 13 14 15 16 17 18 19 20|21 22 23 24| |
+-+-+-+-------------+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--------------+--
0,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 525
1,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
2,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
3,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
4,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
5,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
6,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
7,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
8,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
9,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
a,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
b,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
c,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
d,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
e,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
f,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 N/A
Press: '0 ~ 9' or 'A ~ F' to select channel to edit.
Press: 'M' to move/copy channel configuration.
Press: 'Z' to set ALL channels to factory defaults.
Press 'ESC' to return to Main Menu.
When an input (channel) is selected, the display will show the values
for that particular channel:
Figure 120. Vertical blanking interval setup menu for one channel (NTSC shown).
Vertical Blanking Interval (VBI) -
--------------------------------------------------------------------------------
Reference - Input 0: Line Rate: 525 Line Type: NTSC (M, J)
================================================================================
Selected - Input 0: Line Rate: 525 Line Type: NTSC (M, J)
--------------------------------------------------------------------------------
Disable (Off) 0 NTSC-Reserve Data: VBI:
Enable (On) 1 None 0 None 0
21/284 1 Blank Line Only 1
Notch Decode: 22/285 2 Add Setup Only 2
Notch Decode 1 23/286 3 Setup & Blank 3
Pass Through 2 24/287 4
--------------------------------------------------------------------------------
+------------- Channel Line Rate --------+
| +----------- Notch Decode Mode |
| | +--------- Chroma Kill (On/Off) |
| | | +------- Reserve Line for Data Mode |
| | | | |
| | | | |<-------- VBI Line Pairs ------>|<- Data ->| |
| | | | | | | |
| | | | |E F G H I J K L M N O |P Q R S | |
| | | | |10 11 12 13 14 15 16 17 18 19 20|21 22 23 24| |
+-+-+-+-------------+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--------------+--
0,1,0,0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 525
To Set Notch Decode Mode Press: '['.
To Disable/Enable Chroma Kill Mode press: ']'.
To Set Reserve for Data Mode Press: '\'.
To Set VBI Pair Data Press: 'A' thru 'W'.
Press: 'ESC' to ABORT changes and return to the previous Menu.
Press: 'Enter' to ACCEPT changes and select a different channel.
Press: 'Y' to revert back to last settings.
Press: 'Z' to set THIS channel to factory defaults.
To Next Page
Loading...