GW Instek LCR-6100 - Startup (Continued); Connect to the Device Under Test (DUT)

To Next Page

To Previous Page

LCR-6000 Series User Manual

2.5 Measurement Assistance Functions

2.5.1 Files

Up to 10 setup conditions can be written to/read from

the built-in non-volatile memory.

2.5.2 Key Lock

The front panel keys can be locked.

2.5.3 RS‐232

Complies with SCPI.

2.6 Options

2.6.1 USB host port

Universal serial bus jack, type-A (4 contact positions,

contact 1 is on your left); female;

for connection to USB

memory devices only.

USB disk type: Flash disk only.

Format: FAT / FAT32 / exFAT.

Max memory size: 128GB.

Save Screen

After a USB disk has been inserted into the USB host

port of the LCR meter and if the meter detects that the

USB disk is usable, the meter will show “USB Disk

Ready. Press <Enter> to save screen.” on the lower part

of the LCD screen.

Main Page

Safety Summary3
Table of Contents5
Table of Figures12
List of Tables14
Unpacking and Preperation15
Incoming Inspection15
Environmental Requirements16
Cleaning16
How to Remove the Handle17
Figure 1-1 How to Remove the Handle17
Overview18
Introduction18
Main Specifications and Features19
Test Function19
Equivalent Circuit19
Ranging19
Measurement Speed19
Table 2-1 Equivalent Circuit19
Trigger Mode20
Basic Accuracy20
Display Range20
Table 2-2 Display Range20
Test Signal21
Test Signal Frequency21
Test Signal Level21
Output Impedance21
Main Functions22
Correction Function22
Comparator Function (Sorting)22
List Sweep22
Measurement Assistance Functions23
Files23
Key Lock23
Options23
USB Host Port23
DC Bias Voltage24
Figure 2-1 Disk Ready24
Figure 2-2 Screen Saved24
Startup25
Front Panel25
Figure 3-1 Front Panel25
Table 3-1 Front Panel Description25
Rear Panel26
Power On/Off26
Power on26
Power off26
Figure 3-2 Rear Panel26
Table 3-2 Rear Panel Description26
Warm-Up Time27
Connect to the Device under Test (DUT)27
Figure 3-3 Connect to DUT27
Measure Key28
MEAS DISPLAY] Page28
Measurement Function [FUNC]29
Figure 4-1 [MEAS DISPLAY] Page29
Table 4-1 Measurement Parameter Combinations29
Table 4-2 Monitor Parameters29
Table 4-3 Measurement and Monitor Parameter Descriptions30
Impedance Range [RANGE]31
Table 4-4 Impedance Range Mode31
Table 4-5 Effective Measurement Range for the Impedance Range When in HOLD State32
Table 4-6 DCR FUNC Effective Measurement Range for the Impedance Range When in HOLD State32
Test Frequency [FREQ]33
Table 4-7 Frequency Range and Resolution33
Table 4-8 LCR-6300'S Predefined Test Frequencies that Can be Selected by Using INCR+/DECR34
Table 4-9 LCR-6200'S Predefined Test Frequencies that Can be Selected by Using INCR+/DECR34
Table 4-10 LCR-6100'S Predefined Test Frequencies that Can be Selected by34
Table 4-11 LCR-6020'S Predefined Test Frequencies that Can be Selected by34
Trigger Mode [TRIG]35
Table 4-12 LCR-6002'S Predefined Test Frequencies that Can be Selected by35
Test Signal Voltage/Current Level [LEVEL]36
Table 4-13 Test Voltage/Current Level that Can be Selected with36
Measurement Speed [SPEED]37
Measurement Log [LOG]38
OPEN/SHORT] Page41
Figure 4-2 [OPEN/SHORT] Page41
Open Correction [OPEN]42
Figure 4-3 Stray Admittance42
Short Correction [SHORT]43
Figure 4-4 Residual Impedances43
SPOT Correction44
LIST SETUP] Page46
Measurement Function [FUNC]46
Figure 4-5 [LIST SETUP] Page46
Test Mode [MODE]47
List Measurement Parameters48
List Point and Limit Modes48
LIST MEAS] Page50
Trigger Mode [TRIG]50
Figure 4-6 [LIST MEAS] Page50
Test Mode [MODE]51
Range Mode [RANGE]52
Measurement Log [LOG]52
ENLARGE DISPLAY] Page54
Enlarge Display54
Direct Comparison Function55
Figure 4-7 [ENLARGE DISPLAY] Page55
Figure 4-8 Direct Comparison Setting55
Setup Key56
MEAS SETUP] Page56
Figure 5-1 [MEAS SETUP] Page56
Source Output Impedance [SRC RES]58
Averaging Factor [AVG]58
DC Bias Voltage [BIAS]59
Auto LCZ Function [AUTO LCZ]59
Monitor 1 and Monitor 2 [MON 1][MON 2]60
Measurement Delay [DELAY]61
Auto Level Control [Alc]61
Nominal Value [NOMINAL]61
BIN SETUP] Page62
Measurement Function [FUNC]63
Comparator Function ON/OFF63
Figure 5-2 [BIN SETUP] Page63
Figure 5-3 Page Comparator Workflow64
Auxiliary bin [AUX]65
Primary Parameter Comparator Limit Mode [MODE]65
Figure 5-4 Absolute Mode66
Figure 5-5 Percentage Mode66
Figure 5-6 Sequential Mode67
Nominal Value for Tolerance Mode68
Beep Feature68
Total Number of Bins [#-BINS]68
Lower and Upper Limits69
BIN MEAS] Page69
Comparator Function ON/OFF70
Figure 5-7 [BIN MEAS] Page70
Auxiliary bin [AUX]71
BIN COUNT] Page71
Figure 5-8 [BIN COUNT] Page71
Counter Function [COUNT]72
System Configurations73
SYSTEM CONFIG] Page73
Setting the System Date and Time74
Figure 6-1 [SYSTEM CONFIG] Page74
Account Setting75
KEY BEEP Setting76
Baud Rate76
Hand Shake77
Error Code78
Result79
Data Buffer79
Default Set80
SYSTEM INFO] Page81
Figure 6-2 [SYSTEM INFO] Page81
File Operation82
FILE] Page82
Figure 7-1 [FILE] Page82
Media]83
Recall a File at Startup [AUTO RECALL]83
Auto Save Data to Last File [AUTO SAVE]84
File Operation84
Handler Interface85
Pin Assignment86
Figure 8-1 Pin Assignment86
Table 8-1 Handler Interface Signals ~ Output Pins86
Table 8-2 Handler Interface Signals ~ Input Pins87
Table 8-3 Handler Interface Signals ~ Power Pins87
Connection88
Figure 8-2 Circuit of Input Pins88
Timing Chart for Handler Interface89
Figure 8-3 Circuit of Output Pins (bin Sorting, Index, EOM)89
Figure 8-4 Timing Chart89
Table 8-4 Timing Definitions89
Examples90
Basic Measurement Procedure90
Example91
Figure 9-1 Basic Measurement Procedure91
Figure 9-2 Measurement Results94
Remote Control95
About RS-232C95
Figure 10-1 the RS-232 Connector on the Real Panel95
To Select Baud Rate96
Figure 10-2 PC - LCR-6000 Series Connection Uses a Null Modem Connection96
SCPI Language97
Command Reference98
Terminator98
Notation Conventions and Definitions98
Command Structure98
Figure 11-1 Command Tree Example99
Header and Parameters100
Table 11-1 Multiplier Mnemonics101
Command Reference102
Display Subsystem103
Disp:line103
Disp:page103
Figure 11-2 Command Tree Example103
Function Subsystem105
Function105
Figure 11-3 Function Subsystem Tree105
Function:impedance:auto106
Function:impedance:range106
Function:dcr:range106
Function:range:auto107
Function:monitor1 /2107
Figure 11-4 FREQ Subsystem Command Tree108
Level Subsystem109
Level:voltage (=Voltage[:Level])109
Figure 11-5 Level Subsystem Command Tree109
Level:current (=Current[:Level])110
Level:sresistance (= Voltage:sresistance)110
Level:alc (=Amplitude:alc)111
Level:mode111
Aperture Subsystem112
Aperture:rate112
Aperture:avg112
Figure 11-6 Aperture Subsystem Command Tree112
Fetch Subsystem113
Fetch113
Figure 11-7 Fetch Subsystem Command Tree113
Fetch:impedance114
Fetch:main114
Fetch:monitor1? /2114
Fetch:monitor114
Fetch:list115
Comparator Subsystem116
Figure 11-8 Comparator Subsystem Command Tree116
Comparator:state117
Comparator:mode117
Comparator:aux117
Comparator:bins118
Comparator:tolerance:nominal118
Comparator:tolerance:bin118
Comparator:slim119
Comparator:beep119
Comparator:open120
LIST Subsystem120
List:parameter120
Figure 11-9 LIST Subsystem Command Tree120
List:stat121
List:band121
Correction Subsystem122
Correction:open122
Figure 11-10 Correction Subsystem Command Tree122
Correction:open:state123
Correction:short123
Correction:short:state123
Correction:spot:frequency124
Correction:spot:open124
Correction:spot:short124
Trigger Subsystem125
Trigger[:Immediate]125
Trigger:source125
Figure 11-11 Trigger Subsystem Command Tree125
Trigger:delay126
BIAS Subsystem126
Figure 11-12 BIAS Subsystem Command Tree126
FILE Subsystem127
File127
File:save127
File:load127
Figure 11-13 FILE Subsystem Command Tree127
File:delete128
Error Subsystem128
Error128
SYSTEM Subsystem128
System:shakehand128
System:code129
System:keylock129
System:result129
Common Commands129
Idn129
Trg130
Sav130
Rcl130
Specification131
General Specification131
Dimensions135
Figure 12-1 Dimensions135
Accuracy136
Accuracy137
L, C, R |Z| Measurement Accuracy137
Accuracy for D137
Accuracy for Q138
Accuracy for138
Correction Factors that Affect Measurement Accuracy139
Figure 13-1 the Basic Measurement Accuracy a140
Figure 13-2 Table for Basic Accuracy Correction Factor a141
Table 13-1 Impedance Correction Factors141
Table 13-2 Temperature Correction Factor K142
Table 13-3 Correction Factor for Interpolated Open/Short Trimming K Table 13-4 Correction Factors for the Cable Length of Test Leads K L142
Declaration of Conformity143

GW Instek LCR-6100 - Startup (Continued); Connect to the Device Under Test (DUT)

Table of Contents

Related product manuals