Hakko Electronics FX-100 User Manual

Soldering Station
Instruction Manual
Thank you for purchasing the HAKKO FX-100 Soldering Station.
Please read this manual before operating the HAKKO FX-100.
Keep this manual readily accessible for reference.
1. PACKING LIST AND PART NAMES
HAKKO FX-100 soldering station 1
HAKKO FX-1001 soldering iron 1
Sleeve (Green) 1
Sleeve (Gray) 1
Cleaning wire 1
Heat resistant pad 1
Iron holder 1
Power cord 1
Instruction manual 1
Please check to make sure that all items listed
below are included in the package.
CAUTION
This product includes such features as electrically conductive plastic parts and grounding of the handpiece
and station as measures to protect the device to be soldered from the effects of static electricity. Be sure to
observe the following instructions:
1. The handle and other plastic parts are not insulators, they are conductors. When replacing parts or
repairing, take sufficient care not to expose live electrical parts or damage insulation materials.
2. Be sure to ground the unit during use.
* Specifications and design are subject to change without notice.
HAKKO FX-100
Soldering station
HAKKO FX-1001
Soldering iron
Power cord
Heat resistant
pad
Iron holder
Iron holder
base
Cleaning
sponge
Sleeve
(Green)
Sleeve
(Gray)
Power switch
Receptacle
3. SPECIFICATIONS
Output power
Output frequency
Dimensions
Weight
50 W
13.56 MHz
127 (W) × 150 (H) × 167 (D) mm
(5.0 × 5.9 × 6.6 in.)
3 kg (6.6 lb.)
 Station
 HAKKO FX-1001 soldering iron
Length of cord
Total Length (w/o cord)
Weight (w/o cord)
1.3 m (4.3 ft.)
190 mm (7.5 in.) with T31-02D24 tip
31 g (0.07 lb.) with T31-02D24 tip
NOTE:
This product is protected against electrostatic discharge.
28 W (85 W)
T31-01 Series / 450℃ (840°F)
T31-02 Series / 400℃ (750°F)
T31-03 Series / 350℃ (660°F)
±1.1℃ (±2.0℉)
Power consumption
Tip series /
Tip temperature
Temperature stability
Cleaning wire
2. COMPATIBLE MODELS
Use this product with the following models.
• FX-1001 (Soldering Iron) T31 series (tip for FX-1001)
• FX-1002 (Micro Soldering Iron) T35 series (tip for FX-1002)

Hakko Electronics FX-100 Specifications

General

Control Type	Digital
Weight	1.2 kg
Tip to Ground Potential	< 2mV
Temperature Range	50°C - 450°C
Tip to Ground Resistance	< 2 ohms
Power Consumption	75 W
Heating Element	IH (Induction Heating)

Summary

Specifications

Warnings, Cautions and Notes

General Safety Warnings

Important safety instructions to prevent injury or damage when the unit is hot or in use.

Operational Precautions

Key safety guidelines to prevent accidents or damage to the HAKKO FX-100 during operation.

Initial Setup

Iron Holder Setup

Instructions for setting up the iron holder, including sponge preparation and water addition.

Handpiece Cord Assembly

Steps for assembling the handpiece cord, including passing the cord and inserting the tip.

Station Connection

Guide for connecting the power cord and soldering iron cable to the station.

How to Replace the Sleeve

Operation

Basic Operation

Guide to turning on the unit and navigating the home screen and basic functions.

Mode Screen Navigation

Display Information

Tip Type Selection

Manual Tip Setting

Auto Detect Tip

Parameter Setting

Auto Sleep Function

Auto Shutoff Function

Password Lock

Profile Settings

Maintenance

Tip Maintenance

Cleaning and replacing the soldering iron tip to ensure proper performance.

Cleaning the Tip

Replacing the Fuse

Trouble Shooting Guide