Programmable Temperature & Humidity Controller
42
Event message Description
Ch.1 program operation started (DI1)
Ch.1 program operation is started with contact input(DI1).
Ch.1 program operation stopped (Manual)
Ch.1 program operation is stopped with Stop button.
Ch.1 program operation stopped (Communication)
Ch.1 program operation is stopped by communication.
Ch.1 program operation stopped (DI1)
Ch.1 program operation is stopped with contact input(DI1).
Ch.1 program operation stopped (Error)
Ch.1 program operation is stopped due to an error.
Ch.1 program operation normal stop
Ch.1 program operation is normally stopped.
Ch.1 hold function started (Manual)
Ch.1 hold is started with Ch.1 hold button.
Ch.1 hold function started (Communication)
Ch.1 hold is started by communication.
Ch.1 hold function started (DI2)
Ch.1 hold is started with contact input(DI2).
Ch.1 hold function stopped (Manual)
Ch.1 hold is stopped with Ch.1 hold button.
Ch.1 hold function stopped (Communication)
Ch.1 hold is stopped by communication.
Ch.1 hold function stopped (DI2)
Ch.1 hold is stopped with contact input(DI2).
Ch.1 step function operation (Manual)
Ch.1 step is conducted with Ch.1 step button.
Ch.1 step function operation (Communication)
Ch.1 step is conducted by communication.
Ch.1 step function operation (DI3)
Ch.1 step is conducted with contact input(DI3).
Ch.2 constant-value operation started (Manual)
Ch.1 constant-value operation is started with Run button.
Ch.2 constant-value operation started (Communication)
Ch.1 constant-value operation is started by communication.
Ch.2 constant-value operation started (DI4)
Ch.2 constant-value operation is started with contact input(DI4).
Ch.2 constant-value operation stopped (Manual)
Ch.2 constant-value operation is stopped with Stop button.
Ch.2 constant-value operation stopped (Communication)
Ch.2 constant-value operation is stopped by communication.
Ch.2 constant-value operation stopped (DI4)
Ch.2 constant-value operation is stopped with contact input(DI4).
Ch.2 constant-value operation stopped (Error)
Ch.2 constant-value operation is stopped due to an error.
Ch.2 constant-value operation normal stop
Ch.2 constant-value operation is normally stopped.
Ch.2 program operation started (Manual)
Ch.2 program operation is started with Run button.
Ch.2 program operation started (Communication)
Ch.2 program operation is started by communication.
Ch.2 program operation started (DI4)
Ch.2 program operation is started with contact input(DI4).
Ch.2 program operation stopped (Manual)
Ch.2 program operation is stopped with Stop button.
Ch.2 program operation stopped (Communication)
Ch.2 program operation is stopped by communication.
Ch.2 program operation stopped (DI4)
Ch.2 program operation is stopped with contact input(DI4).
Ch.2 program operation stopped (Error)
Ch.2 program operation is stopped due to an error.
Ch.2 program operation normal stop
Ch.2 program operation is normally stopped.
Ch.2 hold function started (Manual)
Ch.2 hold is started with Ch.2 hold button.
Ch.2 hold function started (Communication)
Ch.2 hold is started by communication.
Ch.2 hold function started (DI5)
Ch.2 hold is started with contact input(DI5).
Ch.2 hold function stopped (Manual)
Ch.2 hold is stopped with Ch.2 hold button.
Ch.2 hold function stopped (Communication)
Ch.2 hold is stopped by communication.
Ch.2 hold function stopped (DI5)
Ch.2 hold is stopped with contact input(DI5).
Ch.2 step function operation (Manual)
Ch.2 step is conducted with Ch.2 step button.
Ch.2 step function operation (Communication)
Ch.2 step is conducted by communication.
Ch.2 step function operation (DI6)
Ch.2 step is conducted with contact input(DI6).
To Next Page
Loading...
