3 - Description
42
3. 5 Tank gauge calibration Setup density of chemical or fertilizer. Calibration for tank size and shape
3. 5. 1 Adjustment of specific gravity Enter weight of liquid fertilizer divided by weight of water (e.g. 1.10 to 1.30)
3. 5. 2 Calibration of Tank gauge Calibrate if factory calibration is not adequate. Disable SafeTrack
3. 5. 2. 1 Water level Fill up the tank to the max level, then press Enter
3. 5. 2. 2 Water level Level the sprayer, then press Enter
3. 5. 2. 3 Water level Empty sprayer through main flow meter at boom. Computer will register flow
3. 5. 2. 4 Calibration of Tank gauge Key in true volume from flowmeter. Computer will calculate table
3. 5. 3 Select factory calibration Select preloaded factory calibration for Hardi tanks or custom calibration
3. 5. 3. 1 Custom calibration of gauge Tank gauge table from custom Calibration
3. 5. 3. 2 Factory calibration Factory tank gauge table
3. 5. 4 Offset at empty MainTank Actual frequency. Accept if empty. Or keyin recorded empty-frequency
3. 6 Track calibration Track width, tractor drawbar length, damping, alignment, sensitivity set up
3. 6. 1 Track width Track width of the sprayer wheels measured center to center
3. 6. 2 Tractor drawbar Measure the length from tractor rear axle to drawbar connection
3. 6. 3 Dead zone for regulation Min value 1 cm and max value 15 cm. Factory setting 5 cm
3. 6. 4 Track sensitivity Control the track sensitivity
3. 6. 4. 1 Accurate
3. 6. 4. 2 Comfort
3. 6. 5 Hitch sensor calibration
3. 6. 5. 1 Hitch sensor calibration Center Sprayer and drive straigth for at least 50m
3. 6. 5. 2 Hitch sensor calibration Angle has to stay in between +-2, adjust chains if out of range
3. 6. 5. 3 Hitch sensor calibration Calibration successful
3. 6. 6 Safety Factor Increasing this value increases the safety. With 100% best safety is achieved.
3. 6. 7 End-stop Calibration
3. 6. 7. 1 End-stop Calibration Set wheelsteer end stop position manually
3. 6. 7. 2 End-stop Calibration Angle must have at least 15 degree (+/-)
3. 6. 7. 3 End-stop Calibration Calibration successful
3. 6. 8 Disable align while reverting
3. 6. 8. 1 Alignment enabled
3. 6. 8. 2 Alignment disabled
4 Toolbox Helpful tools e.g. measure distance and area, service intervals, test etc
4. 1 Service interval: Hours until Work hours remaining for each part until next service is recommended
4. 1. 1 10 hrs Check filters
4. 1. 2 10 hrs Check nozzles
4. 1. 3 50hrs Grease points
4. 1. 4 100hrs Tighten bolts
4. 1. 5 250hrs Misc. check
4. 2 Service interval reset Reset timer counter when service has been carried out
4. 2. 1 Check filters reset Press Enter to reset hour counter, ESC to leave unchanged
4. 2. 2 Check nozzle reset Press Enter to reset hour counter, ESC to leave unchanged
4. 2. 3 Grease points reset Press Enter to reset hour counter, ESC to leave unchanged
4. 2. 4 Tighten bolts reset Press Enter to reset hour counter, ESC to leave unchanged
4. 2. 5 Misc. check reset Press Enter to reset hour counter, ESC to leave unchanged
4. 3 Test Menu Test of components
4. 3. 1 Flow Speed Optional sensors Activate function to monitor sensor (e.g. drive forwards, start flow)
4. 3. 2 Active keys Push key to see if a count is registered. If yes, the key or switch function is OK
4. 3. 3 PrimeFlow test PrimeFlow test for nozzles and PrimeFlow computers on boom
4. 3. 3. 1 PrimeFlow computer status Press Arrow DOWN to see next SMCU Arrow UP to see previous
Menu Number Menu Name Help Text in Display
To Next Page
Loading...
