Hitachi SJ300 Series

15
b031
Software lock mode selection
1.00
Controlled deceleration and stop on power loss
00(Disable)/ 01(Enable)
0.00
1.00
0.00
×
●B GROUP: FINE TUNING FUNCTIONS
b002
b003
b004
b006
b007
b012
b212
b312
b013
b213
b313
b015
b016
b017
b018
b019
b020
b023
b026
b034
b035
b036
b037
b041
b042
b043
b044
b045
b046
b080
b081
b082
b083
b085
b086
b087
b088
b090
b091
b092
b095
b096
b098
b099
Allowable instantaneous power failure time
Time delay enforced before motor restart
Instantaneous power failure and under-voltage trip enable
Phase loss detection enable
Restart frequency threshold
Level of electronic thermal setting
Level of electronic thermal setting for second motor
Level of electronic thermal setting for third motor
Electronic thermal characteristics
Electronic thermal characteristics for second motor
Electronic thermal characteristics for third motor
Free-setting electronic thermal frequency (1)
Free-setting electronic thermal current (1)
Free-setting electronic thermal frequency (2)
Free-setting electronic thermal current (2)
Free-setting electronic thermal frequency (3)
Free-setting electronic thermal current (3)
Deceleration rate at overload restriction
Deceleration rate at overload restriction (2)
RUN/ power-on warning time
Rotational direction restriction
Reduced voltage soft start selection
Function code display restriction
Torque limit(1) (Forward-driving in 4-quadrant mode)
Torque limit(2) (Reverse-regenerating in 4-quadrant mode)
Torque limit(3) (Reverse-driving in 4-quadrant mode)
Torque limit(4) (Forward-regenerating in 4-quadrant mode)
Torque limit LADSTOP enable
Reverse RUN protection enable
AM terminal analog meter adjustment
FM terminal analog meter adjustment
Start frequency adjustment
Carrier frequency setting
Country code for initialization
Frequency scaling conversion factor
STOP key enable
Resume on free-run stop cancellation mode
Dynamic braking usage ratio
Stop mode selection
Cooling fan control
Dynamic braking control
Dynamic braking activation level
Thermistor for thermal protection control
Thermistor for thermal protection level setting
0.3
-
25.0sec.
0.3
-
100.0sec.
00(Disable) / 01(Enable) / 02(Disable during stop and deceleration to stop)
00(Disable) / 01(Enable)
0.00
-
99.99/100.0
-
400.0Hz
0.20
×rated current-1.20×rated current
0.20
×rated current-1.20×rated current
0.20
×rated current-1.20×rated current
00(Reduced torque) / 01(Constant torque) / 02(V/f free-setting)
00(Reduced torque) / 01(Constant torque) / 02(V/f free-setting)
00(Reduced torque) / 01(Constant torque) / 02(V/f free-setting)
0.
- 400.Hz
0.0
- 1000.A
0.
- 400.Hz
0.0
- 1000.A
0.
- 400.Hz
0.0
- 1000.A
0.10
- 30.00
0.10 - 30.00
0.
- 6553(65,530hr) (Output to intelligent terminal)
00(Enabled for both directions)/ 01(Enabled for forward)/ 02(Enabled for reverse)
00(Short)
- 06(Long)
00(All)/ 01(Utilized functions)/ 02(User-selected functions only)
0.
- 200. % / no (Torque limit disable)
0.
- 200. % / no (Torque limit disable)
0.
- 200. % / no (Torque limit disable)
0.
- 200. % / no (Torque limit disable)
00(Disable)/ 01(Enable)
00(Disable)/ 01(Enable)
0
- 255
0
- 255
0.10
- 9.99Hz
0.5
- 15.0kHz (To be derated) [0.5 - 10kHz]
00(Japanese version)/ 01(European version)/ 02(North American version)
0.1
- 99.9
00(Enable) / 01(Disable)
00(Restart at 0Hz) / 01(Resume operation after frequency matching)
0.0
- 100.0%
00(Deceleration to stop) / 01(Free-run stop)
00(Fan is always ON) / 01(Fan is ON during RUN including 5 min. after power-on and stop)
00(Disable) / 01(Enable during run) / 02(Enable during stop)
330
- 380/ 660 - 760V
00(Disable) / 01(PTC enable) / 02(NTC enable)
0.0
- 9999.Ω
Restart after Instantaneous Power Failure
1.0
1.0
00
00
0.00
Rated current
Rated current
Rated current
01
01
01
0.
0.0
0.
0.0
0.
0.0
1.00
1.00
0.
00
06
00
150.
150.
150.
150.
00
00
00
0.0
0.0
180
60
0.50
5.0[3.0]
01
1.0
00
00
0.0
00
00
00
360/720
00
3000.


×
×
×


×
×
×
×
×
×
×
×
×
×
×
×
×
×















×


×
×
×
×


×
×
×
×
×
×






◯
◯
×
×


×
◯
×
×
×
×
×
×
×
×
×

Electronic ThermalOverload Restriction
Software Lock
Others
Selection of automatic restart mode
01
00
×
×


◯
◯
◯


◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯















◯


◯
×
◯
◯


◯
◯
◯
◯
◯
◯
×





◯
◯
◯
◯


×
◯
◯
◯
◯
×
×
◯
◯
◯
◯
×
×
◯
◯
Code
Name
Default Setting
-FE(CE) -FU(UL)
Run-time
Setting
Run-time Data Edit
(Enabled at b031)
Description
b001
00(Alarm output after trip, automatic restart disable) / 01(Restart at 0Hz) / 02(Re-
sume operation after frequency matching)/ 03(Resume previous frequency after
frequency matching, then decelerate to stop and display trip information)
00(All parameters except b031 are locked when SFT from terminal is on)/ 01(All
parameters except b031 and output frequency F001 are locked when SFT from
terminal is on)/ 02(All parameters except b031 are locked)/ 03(All parameters
except b031 and output frequency F001 are locked)/ 10(Run-time data edit
mode)
Number of restarts after instantaneous power
failure and under-voltage trip events
b005 00(16 times) / 01(Always restart)
00 00
Rated
current
×
1.50
Rated
current
×
1.50
00(Disable)/ 01(Enable during accel./constant speed)
/ 02(Enable during constant speed)
/ 03(Enable during accel./constant speed(Speed increase when regenerating))
00(Disable) / 01(Enable during accel./constant speed)
/ 02(Enable during constant speed)
/ 03(Enable during accel./constant speed(Speed increase when regenerating))
01
0.50
×rated current-2.00×rated current [
-
1.80×rated current]
0.50
×rated current-2.00×rated current [
-
1.80×rated current]
b021
Overload restriction operation mode
Overload restriction setting
Overload restriction setting (2)
b024
00(4-quadrant setting)/ 01(Terminal input)/ 02(Analog O2 input)
/ 03(Expansion card 1)/ 04(Expansion card 2)
00
b040
Torque limit selection
00(Trip history clear) / 01(Parameter initialization)
/ 02(Trip history clear and parameter initialization)
b084
Initialization mode
DC bus voltage trigger level during power loss
Over-voltage threshold during power loss
b051
b052
Deceleration time setting during power loss
Initial output frequency decrease during
power loss
0.0
-
1000.V
0.0
-
1000.V
01
00
1.0
1.0
00
00
0.00
Rated current
Rated current
Rated current
01
01
01
0.
0.0
0.
0.0
0.
0.0
1.00
1.00
0.
00
06
00
150.
150.
150.
150.
00
00
00
0.0
0.0
180
60
0.50
5.0[3.0]
02
1.0
00
00
0.0
00
00
00
360/720
00
3000.
01
00
Rated
current
×
1.50
Rated
current
×
1.50
01
00
01
00
×
×
×
×
×
×
×
×
× ×
◯

◯


×
×
×
b054
0.00
-
10.00Hz
×
b022
b050
b053
0.01
-
99.99/100.0
-
999.9/1000.
-
3600.sec.
b025
Overload restriction operation mode (2)
◯
◯
◯
◯
Note:[]75kW and over
= Allowed
= Not permitted
◯
×
[ ]
◯
◯