Hiwin MG Series - Page 60

60
Appendix
Assembly instructions
Linear Guideways
GW-04-0-EN-1910-MA
Series Size Preload class
Z0 ZA ZB
HG 55 6.0 × 10
–4
4.2 × 10
–4
3.4 × 10
–4
65 7.0 × 10
–4
5.0 × 10
–4
4.0 × 10
–4
HG/QH 15 2.6 × 10
–4
1.7 × 10
–4
—
20 2.6 × 10
–4
1.7 × 10
–4
1.0 × 10
–4
25 2.6 × 10
–4
1.7 × 10
–4
1.4 × 10
–4
30 3.4 × 10
–4
2.2 × 10
–4
1.8 × 10
–4
35 4.2 × 10
–4
3.0 × 10
–4
2.4 × 10
–4
45 5.0 × 10
–4
3.4 × 10
–4
2.8 × 10
–4
EG/QE 15 2.6 × 10
–4
1.7 × 10
–4
—
20 2.6 × 10
–4
1.7 × 10
–4
1.0 × 10
–4
25 2.6 × 10
–4
1.7 × 10
–4
1.4 × 10
–4
30 3.4 × 10
–4
2.2 × 10
–4
1.8 × 10
–4
35 4.2 × 10
–4
3.0 × 10
–4
2.4 × 10
–4
CG 15 – 45 2.8 × 10
–4
1.7 × 10
–4
1.2 × 10
–4
WE 15 1.3 × 10
–4
0.4 × 10
–4
—
50 3.4 × 10
–4
2.2 × 10
–4
1.8 × 10
–4
WE/QW 21 2.6 × 10
–4
1.7 × 10
–4
0.9 × 10
–4
27 2.6 × 10
–4
1.7 × 10
–4
0.9 × 10
–4
35 2.6 × 10
–4
1.7 × 10
–4
1.4 × 10
–4
RG 15 – 65 2.2 × 10
–4
1.7 × 10
–4
1.2 × 10
–4
QR 25 – 45 2.2 × 10
–4
1.7 × 10
–4
1.2 × 10
–4
Table 12.4 Coefficient of the height tolerance (K)
Series Size Preload class
ZF Z0 Z1
MG 05 0.4 × 10
–4
0.4 × 10
–4
0.04 × 10
–4
07 0.5 × 10
–4
0.5 × 10
–4
0.06 × 10
–4
09 0.7 × 10
–4
0.7 × 10
–4
0.12 × 10
–4
12 1.0 × 10
–4
1.0 × 10
–4
0.24 × 10
–4
15 1.2 × 10
–4
1.2 × 10
–4
0.40 × 10
–4
Table 12.5 Coefficient of the height tolerance (K) – MG series