Honeywell DC33XB

To Next Page

To Previous Page

Linjajännitteiset vaihtovirta liittimet

N:o 2 sisääntuloliittimet ; 2 HLAI sisääntuloliittimet

N:o 1 sisääntuloliittimet

Lähetinteho 4 - 20 mA 2-johtoiselle lähettimelle

Numeeriset siääntuloliittimet

Ulostulo- ja hälytysliittimet

Lisäliittimet ulostulolle

Tietoliikenneliittimet

Main Page

Table of Contents3
Introduction7
Overview7
CE Conformity (Europe)7
Figure 1-1 Operator Interface Displays and Indicators7
Function Keys8
Table 1-1 Function of Keys8
Installation9
Mounting9
Figure 2-1 Dimensions9
Wiring10
Figure 2-2 Mounting Method10
Table 2-1 Permissible Wiring Bundling11
Figure 2-3 Composite Wiring Diagram12
Figure 2-4 Line Voltage Wiring13
Figure 2-5 Input #1/#2 Connections14
Table 2-2 Input 2 Jumper Selections15
Figure 2-6 Electromechanical Relay Output - Model DC330X-EE-XXX15
Figure 2-7 Solid State (SS) Relay Output - Model DC33X-AA-XX16
Figure 2-8 10-Amp SS External Relay Output - Model DC330X-SS-XX16
Figure 2-9 Open Collector Output - Model DC330X-TT-XXX17
Figure 2-10 Current Output Current/Time Duplex, Time/Current Duplex, Position Proportional or Three Position Step Control18
Figure 2-11 Auxiliary Output and Three-Relay Output18
Figure 2-12 Position Proportional Output or Three Position Step-Models19
Figure 2-13 Auxiliary Output Connections- Models DC330X-XX-2XX20
Figure 2-14 Digital Inputs Connections-Model DC330X-XX-XX320
Figure 2-15 RS422/485/ASCII or Modbus Communications Option Connections21
Dc330X-XX-5Xx22
Figure 2-16 Transmitter Power for 4-20 Ma 2-Wire Transmitter Using Open Collector Alarm 2 Output-Model DC330X-XT-XXX22
Figure 2-17 Transmitter Power for 4-20 Ma 2-Wire Transmitter Using Auxiliary Output-Model DC330X-XX-2XX or DC330X-XX-5XX22
Table 2-3 Control Relay Contact Information23
Table 2-4 Alarm Relay Contact Information23
Configuration25
Overview25
Figure 3-1 Prompt Hierarchy25
Configuration Procedure27
Table 3-1 Configuration Procedure27
Loop 1 Tuning Parameters Set up Group28
Table 3-2 Tuning Group Function Prompts28
SP Ramp, SP Rate, or SP Programming Set up Group30
Table 3-3 SP Ramp Function Prompts30
Accutune Set up Group32
Algorithm Data Set up Group32
Table 3-4 Accutune Group Function Prompts32
Table 3-5 Algorithm Group Function Prompts32
Output Algorithm Parameters Set up Group34
Table 3-6 Output Algorithm Group Function Prompts34
Input 1 Parameters Set up Group35
Table 3-7 Input 1 Group Function Prompts35
Input 2 Parameters Set up Group36
Table 3-8 Input 2 Group Function Prompts36
Loop 1 Control Parameters Set up Group37
Table 3-9 Control Group Function Prompts37
Options Set up Group39
Table 3-10 Options Group Function Prompt39
Communications Set up Group40
Table 3-11 Communications Group Function Prompts40
Alarms Set up Group42
Table 3-12 Alarms Group Function Prompts42
Display Parameters Set up Group44
Calibration Group44
Status Group44
Table 3-13 Display Group Function Prompts44
Operation45
How to Power up the Controller45
Monitoring Your Controller45
Table 4-1 Lower Display Key Parameter Prompts46
Table 4-2 Error Messages47
Start-Up Procedure48
Table 4-3 Procedure for Starting up the Controller48
Operating Modes49
Setpoints49
Using Two Sets of Tuning Constants50
Table 4-4 Setpoint Selection Indication50
Table 4-5 Procedure for Selecting Two Sets of Tuning Constants50
Table 4-6 Procedure for Setting Switchover Values50
Table 4-7 Procedure for Setting Tuning Constant Values51
Table 4-8 Procedure for Switching PID SETS from the Keyboard51
Alarm Setpoints52
Three Position Step Control Algorithm52
Table 4-9 Procedure for Displaying or Changing the Alarm Setpoints52
Table 4-10 Procedure for Displaying the 3PSTEP Motor Position52
Input Math Algorithms53
Digital Input Option (Remote Switching)54
Table 4-11 Digital Input Option Action on Contact Closure54
Table 4-12 Digital Input Combinations "DIG IN1" or "DIG IN255
Fuzzy Overshoot Suppression56
Accutune56
Table 4-13 Procedure for Starting TUNE (Demand) Tuning57
Entering a Security Code58
Table 4-14 Procedure for Using TUNE at Start-Up for Duplex58
Table 4-15 Procedure to Enter a Security Code58
Setpoint Rate/Ramp/Soak Program Operation59
Setpoint Ramp Rate59
Single Setpoint Ramp59
Table 5-1 Procedure for Running a Setpoint Ramp60
Setpoint Ramp/Soak Programming Option61
Table 5-2 Program Contents62
Figure 5-1 Ramp/Soak Profile Example64
Figure 5-2 Program Record Sheet65
Table 5-3 Run/Monitor Functions66
Appendix A - Environmental and Operating Conditions69
Appendix B - Model Selection Guide71
Appendix C - Configuration Record Sheet73
Appendix D - Position Proportional Calibration75
Position Proportional Control Output Calibration75
Table 9-1 Calibration Procedure76
Appendix E - Input Ranges79

Honeywell DC33XB - Page 84

Table of Contents

Related product manuals