6 - 43
Profile Parameters
Setting Default Explanation
Edit Profile Default A string of 1 to 32 alphanumeric characters, establishes the name of the Pro-
file.
Options are Default or ThirdPartyConfig.
SSID Blank A string of up to 32 alphanumeric characters. Establishes the Service Set Iden-
tifier (SSID) of the WLAN to which the client connects.
Client Name Blank A string of up to 16 characters. The client name is assigned to the network card
and the device using the network card. The client name may be passed to net-
working wireless devices, e.g., Access Points.
Power Save Fast Power save mode is On.
Options are: Constantly Awake Mode (CAM) power save off, Maximum (power
saving mode) and Fast (power saving mode).
Tx Power Maximum Maximum setting regulates Tx power to the Max power setting for the current
regulatory domain.
Options are: Maximum, 50mW, 30mW, 20mW, 10mW, 5mW, or 1mW.
Bit Rate Auto Setting the rate to Auto will allow the Access Point to automatically negotiate
the bit rate with the client device.
Options are: Auto, 1 Mbit, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 or 54 Mbit.
Auth Type Open 802.11 authentication type used when associating with the Access Point.
Options are: Open, LEAP, or Shared key.
EAP Type None Extensible Authentication Protocol (EAP) type used for 802.1x authentication
to the Access Point.
Options are: None, LEAP, EAP-FAST, PEAP-MSCHAP, PEAP-GTC, PEAP-
TLS, EAP-TTLS, or EAP-TLS.
EAP Type chosen determines whether the Credentials button is active and
also determines the available entries in the Credentials pop-up window.
Encryption None Type of encryption to be used to protect transmitted data. Available options
may vary by SCU version.
Options are: None, WEP (or Manual WEP), WEP EAP (or Auto WEP), WPA
PSK, WPA TKIP, WPA CCKM, WPA2 PSK, WPA2 AES, or WPA2 CCKM.
CKIP is not supported in the Marathon.
Note: The Encryption type chosen determines if the WEP Keys / PSK Keys
button is active and also determines the available entries in the WEP or
PSK pop-up window.
Radio Mode BGA Rates
Full
Specify 802.11a, 802.11b and/or 802.11g rates when communicating with the
AP. The options displayed for this setting depend on the type of radio installed
in the mobile device.
Options:
B rates only (1, 2, 5.5 and 11 Mbps)
BG Rates Full (All B and G rates)
G rates only (6, 9, 12, 18, 24, 36, 48 and 54 Mbps)
BG optimized or BG subset (1, 2, 5.5, 6, 11, 24, 36 and 54 Mbps)
A rates only (6, 9, 12, 18, 24, 36, 48 and 54 Mbps)
ABG Rates Full (All A rates and all B and G rates with A rates preferred)
BGA Rates Full (All B and G rates and all A rates with B and G rates
preferred)
Ad Hoc (when connecting to another client device instead of an AP)
Default:
BGA Rates Full (for 802.11a/b/g/n radio)
It is important the Radio Mode setting correspond to the Access Point to which
the device is to connect. For example, if this setting is set to G rates only, the
Marathon may only connect to Access Points set for G rates and not those set
for B and G rates.
To Next Page
Loading...
