Honeywell MiniRAE 3000+ - Page 70

126 pages

To Next Page

To Previous Page

MiniRAE 3000+, ppbRAE 3000+, UltraRAE 3000+

MiniRAE Lite+

Note: When you reach Monitor Setup and press [N/-], the menu cycles back to Calibration.

Handheld PID Monitors 70 User Manual

Main Page

default chapter2
- Table of Contents2
Chapter 1 - Introduction7
- Product Registration7
- Standards and Certifications7
- Safety9
- Read before Operating10
- Proper Product Disposal at End of Life11
- Standard Package Contents14
Chapter 2 - General Information15
- Key Features15
- Physical Description16
Chapter 3 - Charging the Battery17
- Charging a Spare Rechargeable Battery19
- Replacing Rechargeable Li-Ion Battery19
- Low Voltage Warning19
- Clock Battery20
- Data Protection While Power Is off20
- Alkaline Battery Pack20
Chapter 4 - Basic Operation21
- Turning the Instrument on21
- Turning the Instrument off21
Chapter 5 - User Interface22
- Display24
- Icons26
Chapter 6 - Operating the Instrument27
- Turning the Instrument on27
- Turning the Instrument off27
- Auto-Zero at Startup28
- Operating the Built-In Flashlight28
- Pump Status29
- Calibration Status29
- Bump Status30
- Glance Mode30
- Enter Glance Mode30
- Glance Mode Screens31
- Exit Glance Mode31
- Reverse Direction Navigation32
- Policy Enforcement32
- Setting Policy Enforcement33
Chapter 7 - Operating Modes36
- Minirae 3000+ & Ppbrae 300036
- Basic User Level/Hygiene Mode37
- Ultrarae 300038
Chapter 8 - Ultrarae 3000+ Operation40
- Compound-Specific Measurement40
- Measurement Phases40
- Performing a Measurement40
- Separation Tube Preparation42
- Inserting the Separation Tube43
- Measuring44
Chapter 9 - VOC Operation - Ultrarae300047
- Basic User Level/Hygiene Mode (Default Settings)47
- Basic Operation - Minirae 300048
Chapter 10 - Alarm Signals49
- Alarm Signal Summary49
- Preset Alarm Limits & Calibration50
- Testing the Alarm50
- Integrated Sampling Pump51
- Backlight51
- Datalogging51
- Datalogging Event51
- Datalogging Sample51
- Auto/Manual/Snapshot Datalogging52
Chapter 11 - Standard Kit & Accessories53
- Accessories53
- AC Adapter (Battery Charger)55
- Alkaline Battery Adapter56
- External Filter57
- Optional Accessories58
- Calibration Adapter58
- Calibration Regulator58
- Organic Vapor Zeroing Kit58
- Autorae 2 Automatic Test & Calibration System58
Chapter 12 - Calibration59
- Standard Two-Point Calibration59
- Entering Calibration60
- Zero (Fresh Air) Calibration61
- Span Calibration62
- Exiting Two-Point Calibration in Basic User Level63
- Three-Point Calibration64
- Span 2 Calibration65
- Exiting Three-Point Calibration66
Chapter 14 - Bump Test67
Chapter 15 - Programming Mode68
- Entering Programming Mode69
- Programming Mode Menus71
- Exiting Programming Mode72
- Navigating Programming Mode Menus72
- Reverse Direction - Menu Selection73
- Calibration73
- Measurement75
- Datalog82
- Monitor Setup85
Chapter 16 - Hygene Mode93
- Basic User Level & Hygiene Mode93
- Entering Search Mode from Hygiene Mode94
Chapter 17 - Advanced User Level95
- Advanced User Level & Hygiene Mode95
- Basic User Level & Search Mode96
- Advanced User Level & Search Mode97
Chapter 18 - Diagnostic Mode98
- Entering Diagnostic Mode98
- Adjusting the Pump Stall Threshold99
- Testing the Humidity Sensor100
- Exiting Diagnostic Mode101
Chapter 19 - Transferring Data102
- Downloading the Datalog to a PC102
- Uploading Firmware to the Instrument from a PC103
Chapter 20 - Maintenance104
- Battery Charging & Replacement104
- Replacing the Li-Ion Battery105
- Replacing the Alkaline Battery Adapter106
- PID Sensor & Lamp Cleaning/Replacement107
- Cleaning the PID Sensor110
- Cleaning the Lamp Housing or Changing the Lamp110
- Determining the Lamp Type111
- Sampling Pump112
- Cleaning the Instrument112
- Special Servicing Note112
Chapter 21 - Specifications113
- Minirae Lite+ Specifications113

Honeywell MiniRAE 3000+ - Page 70

Table of Contents

Related product manuals