To Next Page

To Previous Page

149

[SwitchA-Ten-GigabitEthernet1/0/7] quit

[SwitchA] interface ten-gigabitethernet 1/0/8

[SwitchA-Ten-GigabitEthernet1/0/8] priority-flow-control enable

[SwitchA-Ten-GigabitEthernet1/0/8] priority-flow-control no-drop dot1p 3

[SwitchA-Ten-GigabitEthernet1/0/8] qos trust dot1p

[SwitchA-Ten-GigabitEthernet1/0/8] quit

[SwitchA] interface ten-gigabitethernet 2/0/5

[SwitchA-Ten-GigabitEthernet2/0/5] priority-flow-control enable

[SwitchA-Ten-GigabitEthernet2/0/5] priority-flow-control no-drop dot1p 3

[SwitchA-Ten-GigabitEthernet2/0/5] qos trust dot1p

[SwitchA-Ten-GigabitEthernet2/0/5] quit

[SwitchA] interface ten-gigabitethernet 2/0/6

[SwitchA-Ten-GigabitEthernet2/0/6] priority-flow-control enable

[SwitchA-Ten-GigabitEthernet2/0/6] priority-flow-control no-drop dot1p 3

[SwitchA-Ten-GigabitEthernet2/0/6] qos trust dot1p

[SwitchA-Ten-GigabitEthernet2/0/6] quit

[SwitchA] interface ten-gigabitethernet 2/0/7

[SwitchA-Ten-GigabitEthernet2/0/7] priority-flow-control enable

[SwitchA-Ten-GigabitEthernet2/0/7] priority-flow-control no-drop dot1p 3

[SwitchA-Ten-GigabitEthernet2/0/7] qos trust dot1p

[SwitchA-Ten-GigabitEthernet2/0/7] quit

[SwitchA] interface ten-gigabitethernet 2/0/8

[SwitchA-Ten-GigabitEthernet2/0/8] priority-flow-control enable

[SwitchA-Ten-GigabitEthernet2/0/8] priority-flow-control no-drop dot1p 3

[SwitchA-Ten-GigabitEthernet2/0/8] qos trust dot1p

[SwitchA-Ten-GigabitEthernet2/0/8] quit

5. Configure ETS:

# Configure the 802.1p-local priority mapping table as follows:

{ Map 802.1p priority value 3 to local precedence 1.

{ Map the other 802.1p priority values to local precedence 0.

[SwitchA] qos map-table dot1p-lp

[SwitchA-maptbl-dot1p-lp] import 3 export 1

[SwitchA-maptbl-dot1p-lp] import 0 export 0

[SwitchA-maptbl-dot1p-lp] import 1 export 0

[SwitchA-maptbl-dot1p-lp] import 2 export 0

[SwitchA-maptbl-dot1p-lp] import 4 export 0

[SwitchA-maptbl-dot1p-lp] import 5 export 0

[SwitchA-maptbl-dot1p-lp] import 6 export 0

[SwitchA-maptbl-dot1p-lp] import 7 export 0

[SwitchA-maptbl-dot1p-lp] quit

# Enable byte-count WRR on interface Ten-GigabitEthernet 1/0/1.

[SwitchA] interface ten-gigabitethernet 1/0/1

[SwitchA-Ten-GigabitEthernet1/0/1] qos wrr byte-count

# Configure WRR on interface Ten-GigabitEthernet 1/0/1 as follows:

{ Assign 50% of the interface bandwidth to the FCoE traffic (traffic assigned to queue 1).

{ Assign 50% of the interface bandwidth to Ethernet data traffic (traffic assigned to queue 0).

[SwitchA-Ten-GigabitEthernet1/0/1] qos wrr af1 group 1 byte-count 1

Other manuals for HP FlexFabric 5700 series

Security Configuration Guide460 pages

Questions and Answers:

Need help?

Do you have a question about the HP FlexFabric 5700 series and is the answer not in the manual?

HP FlexFabric 5700 series Specifications

General

Layer Support	L2/L3
Routing Protocol	OSPF, BGP, RIP, IS-IS, Static Routing
Remote Management Protocol	SNMP, CLI, Web
Features	VXLAN
Compliant Standards	IEEE 802.1D, 802.1Q, 802.1w, 802.1s, 802.3ad
Operating Temperature	0°C to 45°C
Operating Humidity	10% to 90% (non-condensing)
VLANs	4K