What causes my HTC DURATIQ T6 Floor Machine to lose contact with other units?
If your HTC Floor Machine loses contact with other units, the CAN bus signal may be broken. Check the cable connections on the connection panel.
What to do if there is a low water level in the tank of my HTC DURATIQ T6?
If there is a low water level in the tank of your HTC Floor Machine, top up the water and check the level sensor.
How to reset the emergency stop on my HTC DURATIQ T6 Floor Machine?
To reset the emergency stop on your HTC Floor Machine, reset the emergency stop button. Check the remote control and reconnect the radio using the connection button.
How do I fix an error on the CAN bus of my HTC DURATIQ T6 Floor Machine?
To fix an error on the CAN bus of your HTC Floor Machine, check the cabling and the units connected to the HMI.
What to do if the grinding motor overheats in my HTC DURATIQ T6?
If the grinding motor overheats in your HTC Floor Machine, check the motor's cooling fan and reduce the motor's load. Refer to the meter for motor current.
How to troubleshoot low input voltage to my HTC DURATIQ T6?
To troubleshoot low input voltage to your HTC Floor Machine, check the voltage level during operation, the cable area, and the electrical supply.
What should I do if the grinding motor is overloaded on my HTC DURATIQ T6?
If the grinding motor is overloaded on your HTC Floor Machine and the overload meter exceeds 90%, reduce the motor's load. Refer to the meter for motor current.
How to reduce high temperature in the electrical cabinet of my HTC Floor Machine?
To reduce high temperature in the electrical cabinet of your HTC Floor Machine, clean the fans and cooling flange. Ensure the fans are rotating during grinding and for 1 minute after finishing, as well as when needed. Allow the machine to cool down.
Why my HTC DURATIQ T6 cannot cope?
If your HTC Floor Machine cannot cope, consider these potential causes and solutions: * Too high a load: Reduce the grinding pressure. * If the cause is not listed: If the machine runs at high speed, lower the revs per minute to make the machine stronger. Refer to the meter for available power. * Voltage drop: Check the voltage meter during grinding. * Too sticky a coating on the surface: Run half of the machine on the surface to be cleaned and half on the clean surface to remove residue from the tools. * If the cause is not listed: Check the tools to ensure the correct tools are used, that they are in working order and correctly fitted.
Why does the fuse keep tripping on my HTC Floor Machine?
A fuse might trip on your HTC Floor Machine due to: * Too high a load or too small fuses: Check the size and inertia of the fuses. * If the cause is not listed: Reduce the machine's load by reducing the grinding pressure, lowering the revs per minute, or changing the tool. Refer to the machine's power meter.
General| Brand | HTC |
|---|---|
| Model | DURATIQ T6 |
| Category | Floor Machine |
| Language | English |
Explanation of warning symbols and essential safety rules for machine operation.
Details on important safety decals and warnings affixed to the machine.
Data on hand-arm vibrations and sound power levels according to relevant standards.
Diagram and numbering of the Human-Machine Interface (HMI) control panel.
Detailed explanation of each function and button on the control panel.
Visual representation and numbering of the machine's information display panel.
Explanation of the various symbols and their meanings on the information panel.
Description of the data metrics shown on the information panel.
Instructions for adjusting the machine's handle for optimal working height.
Procedure for adjusting the machine's weights to optimize grinding pressure.
How to control machine movement and grinding process using the control panel.
Detailed steps for performing manual grinding operations.
Steps for setting up and pairing the remote control with the machine.
Specific controls for grinding speed, propulsion, and offset via radio.
Common causes and solutions when the machine fails to start.
Troubleshooting for frequent tripping of fuses or earth fault breakers.
Solutions for when the machine cannot cope or performs poorly.
Overview of how warnings and error messages are displayed on the machine.
Explanation of specific warning messages and how to erase them.
Actions to take for various warning messages like voltage or temperature issues.
Explanation of specific error messages and their fault descriptions.
Actions to take for error messages like CAN bus errors or motor faults.
To Next Page
