Why does called party disconnect repeatedly during communication on Hytera PD68X Portable Radio?
If the called party disconnects repeatedly during communication on your Hytera Portable Radio, the signal may be intermittent or weak. Make sure the radio is within the coverage of the BS.
What to do if Hytera Portable Radio cannot establish a call?
If your Hytera Portable Radio cannot establish a call, the signal may be weak. Make sure the radio is within the coverage of the BS.
What to do if voice is weak or discontinuous on Hytera PD68X?
If the voice is weak or discontinuous during receiving on your Hytera Portable Radio, try the following: * Recharge or replace the battery, as the battery voltage may be low. * Increase the volume, as the volume level may be low. * Turn off the radio, and then remove and reattach the antenna, as the antenna may be loose or installed incorrectly. * Clean the surface of the speaker, as it may be blocked.
How to fix Hytera Portable Radio if it won't turn on?
If your Hytera Portable Radio won't turn on, the battery may be installed improperly. Remove and reattach the battery. Also, the battery power might have run out, so recharge or replace the battery. Finally, the battery contacts may be dirty or damaged. Clean the battery contacts or replace the battery.
What to do if I hear noise on Hytera Portable Radio channel?
If you are experiencing irrelevant communication or noise on your Hytera Portable Radio channel, it could be due to radios using the same frequency. Try changing the frequency or adjusting the squelch level. Another possibility is that the radio is set with no signaling. In this case, set signaling for all member radios to avoid interference at the same frequency, and ensure you change the signaling settings for all portable radios simultaneously.
Why is there so much noise on my Hytera PD68X Portable Radio?
Excessive noise on your Hytera Portable Radio could be due to several factors. You might be too far from other members, so try moving closer. Your location could be unfavorable, such as being blocked by buildings or underground, so move to an open area and restart the radio. Also, external electromagnetic interference could be the cause, so move away from potential sources of interference.
How to fix communication issues with my Hytera PD68X Portable Radio?
If you cannot communicate with other members using your Hytera Portable Radio, consider these solutions: Ensure that your TX/RX frequency and signaling match those of the other members. Also, verify that all members are using the same channel type (digital or analog). Finally, make sure you are not too far away from the group members; try moving closer.
Why is the voice weak on my Hytera PD68X?
If the voice is weak, discontinuous, or totally inactive during receiving on your Hytera Portable Radio, consider these potential causes: the battery voltage might be low, so recharge or replace the battery. Alternatively, the volume level could be set too low; increase it using the Volume Control knob. Also, ensure the antenna is properly attached by reassembling it after turning off the radio.
General| Channel Capacity | 256 |
|---|---|
| Zone Capacity | 16 |
| Battery Capacity | 2000 mAh |
| IP Rating | IP67 |
| Audio Output Power | 1 W |
| Channel Spacing | 12.5/20/25 kHz |
| Operating Voltage | 7.4 V |
| Channels | 256 |
| Operating Temperature | -30°C to +60°C |
| Display | LCD |
| Transmit Power | UHF: 1W/4W; VHF: 1W/5W |
| Storage Temperature | -40℃ ~ +85℃ |
| Digital Protocol | DMR |
How to power on/off, adjust volume, and check battery.
Locking keys, using keypad, and switching operation modes.
Meanings of icons on LCD for modes and basic status.
Icons indicating short data and call statuses.
Explains the different states of the LED indicator lights.
How to start a group communication.
Steps to make one-to-one calls and calls to telephone numbers.
Procedures for various call types like all-call, broadcast, and analog.
Accessing, composing, and sending new, quick text, and status messages.
To Next Page
