Table 1. Features and specifications
Microprocessor:
v Supports one Intel quad-core (Xeon
3400 series) or dual-core (Celeron
G1101, Pentium G6950, or Core i3
series) processor the IbexPeak 3420
chip set and Multi-chip Package
processor architecture
v Designed for LGA 1156 socket
v Scalable up to four cores
v 32 KB instruction cache, 32 KB data
cache, and up to 8 MB L3 cache that is
shared among the cores
v Support for Intel Extended Memory 64
Technology (EM64T)
Note:
v Use the Setup utility to determine the
type and speed of the microprocessors.
v For a list of supported microprocessors,
see http://www.ibm.com/servers/eserver/
serverproven/compat/us/.
Memory:
v Minimum: 1 GB
v Maximum: 32 GB
– 16 GB using unbuffered DIMMs
(UDIMMs)
– 32 GB using registered DIMMs
(RDIMMs)
v Types: PC3-8500 or PC3-10600
(single-rank or dual-rank), ECC
unbuffered or registered
double-data-rate 3 (DDR3) 1066 or
1333 MHz registered or unbuffered
SDRAM DIMM
v Connectors: six dual inline memory
module (DIMM) connectors, two-way
interleaved
v Supports:
– 1 GB, 2 GB, and 4 GB unbuffered
DIMMs
– 1 GB, 2 GB, 4 GB, and 8 GB
registered DIMMs
Integrated functions:
v Integrated management module (IMM),
which provides service processor
control and monitoring functions, video
controller, and (when the optional virtual
media key is installed) remote
keyboard, video, mouse, and remote
hard disk drive capabilities
v Intel 82574L Gb Ethernet controller
v Integrated Trusted Platform Module
(TPM) support
v Integrated SATA controller (simple-swap
and hot-swap models)
v Seven Universal Serial Bus (USB) 2.0
ports (two front and four rear of the
chassis), one internal for the optional
USB Hypervisor key.
v One serial port
v Two Ethernet ports
v One system-management RJ-45 on the
rear to connect to a systems
management network. This system
management connector is shared to the
IMM functions. This connector is active
with or without the optional IBM Virtual
Media Key installed.
v Six SATA II ports (four through the
iPASS connector for simple-swap drives
and two for the optical DVD and tape
drives)
RAID controllers:
v A ServeRAID-BR10il v2 SAS/SATA
adapter that provides RAID levels 0, 1,
and 1E (comes standard on some
hot-swap SAS and hot-swap SATA
models).
v An optional ServeRAID-MR10i
SAS/SATA adapter that provides RAID
levels 0, 1, 5, 6, and 10 can also be
ordered.
v An optional ServeRAID-MR10is
SAS/SATA adapter that provides RAID
levels 0, 1, 5, 6, and 10 can also be
ordered.
Environment:
v Air temperature:
– Server on: 10°C to 35°C (50°F to
95°F)
Altitude: 0 to 914.4 m (3000 ft)
– Server on: 10°C to 32°C (50°F to
89.6°F)
Altitude: 914.4 m (3000 ft) to 2133.6
m (7000 ft)
– Server off: 10°C to 43°C (50°F to
109.4°F)
Maximum altitude: 2133.6 m (7000.0
ft)
– Shipping: -40°C to 60°C (-40°F to
140°F)
v Humidity (operating and storage): 8% to
80%
v Particulate contamination:
Attention: Airborne particulates and
reactive gases acting alone or in
combination with other environmental
factors such as humidity or temperature
might pose a risk to the server. For
information about the limits for
particulates and gases, see “Particulate
contamination” on page 249.
Drives (depending on the model):
v Diskette (optional): External or internal
USB FDD drive and memory key
v Hard disk drives: Hot-swap SAS,
hot-swap SATA, or simple-swap SATA
(support AHCI mode)
v One of the following SATA attached
optical drives:
– DVD-ROM
– Multiburner (optional)
Drive bays (depending on the model):
v Two 5.25 in. half-high bays (one optical
drive installed).
v One 3.5 in. slim-high removable-media
drive bay (optional diskette drive)
v Four 3.5 in. slim-high hard disk drive
bays (some models)
v Eight 2.5 inch slim-high hard disk drive
bays (some models)
Fans:
Three speed-controlled fixed fans
Power supply:
One of the following power supplies:
v One or two redundant 430-watt (90-240
V ac) with Active Energy Manager
v One non-redundant 401-watt (90-240 V
ac) without Active Energy Manager
Size:
v Height: 438 mm (17.25 in.)
v Depth: 540 mm (21.25 in.)
v Width: 216 mm (8.5 in.)
v Weight: 19.6 kg (43 lb) to 21.4 kg (47
lb) depending upon configuration
Heat output:
Approximate heat output:
v Minimum configuration: 188 Btu per
hour (55 watts)
v Maximum configuration: 1784 Btu per
hour (523 watts)
Electrical input:
v Sine-wave input (50 or 60 Hz) required
v Input voltage and frequency ranges
automatically selected
v Input voltage low range:
– Minimum: 100 V ac
– Maximum: 127 V ac
v Input voltage high range:
– Minimum: 200 V ac
– Maximum: 240 V ac
v Input kilovolt-amperes (kVA)
approximately:
– Minimum: 0.20 kVA (all models)
– Maximum: 0.55 kVA
Chapter 2. Introduction
7
To Next Page
Loading...
Need help?
General
