Icom IC-756 - Fine and Memory Scan Operations

49
6
SCANS
Fine scan functions as programmed or ∂F scan, but
scan speed decreases when the squelch opens and
does not stop. The scanning tuning step shifts from
50 Hz to 10 Hz while the squelch opens.
q Select the scan screen from the start up screen by
pushing [(F-4)SCAN].
w Set for programmed scan or ∂F scan as described
on previous page.
e Push [
(F-1)PROG] or [(F-2)∂F] to start a scan.
- Decimal points blink while scanning.
r Push [(F-3)FINE] to start a fine scan.
- “FINE PROGRAM SCAN” or “FINE ∂F SCAN” ap-
pears.
t When the scan detects a signal, the scan speed
decreases but does not stop.
y Push [(F-1)PROG] or [(F-2)∂F] to stop the scan;
push [(F-3)FINE] to cancel the fine scan.
■ Fine programmed scan/fine
∂∂
F scan
2.4k2.4k9 2.8k2.8k455455
12:3412:34
Programmed P1:0.500.00MHz
Scan edges P2: 29.999.99MHz
∂ F  Span: ±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANFINEFINE EXITEXITPROGPROG
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
 PROGRAM SCAN
1ß
14.195.00
VFOVFO
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO
2.4k2.4k9 2.8k2.8k455455
12:3412:34
Programmed P1:0.500.00MHz
Scan edges P2: 29.999.99MHz
∂ F  Span: ±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANFINEFINE EXITEXITPROGPROG
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
 FINE PROGRAM SCAN
1ß
14.195.00
VFOVFO
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO
q If the start up screen is not selected (if [F-5]’s func-
tion is [EXIT]), push [F-5] one or more times to exit.
w Select memory mode.
e Select the desired operating mode.
- The operating mode can also be changed while scan-
ning.
r Push [
(F-4)
SCAN] to select the scan screen.
t Set [RF/SQL] open or closed.
- See p. 47 for scan condition.
- If the [RF/SQL] control function is set as RF control, the
squelch always opens. See pgs. 2, 56 for details.
y Push [(F-1)MEMORY] to start the memory scan.
- Decimal points blink while scanning.
u When the scan detects a signal, the scan stops,
pauses or ignores it depending on the resume set-
ting and the squelch condition.
i To cancel the scan, push [(F-1)MEMORY].
NOTE: 2 or more memory channels must be pro-
grammed for memory scan to start.
■ Memory scan operation
2.4k2.4k9 2.8k2.8k455455
12:3412:34
Programmed P1:0.500.00MHz
Scan edges P2: 29.999.99MHz
∂ F  Span: ±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANSELECTSELECT EXITEXITMEMORYMEMORY
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
VFOVFO
14.195.00
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO
1212
MEMORYMEMORY
2.4k2.4k9 2.8k2.8k455455
12:3412:34
Programmed P1:0.500.00MHz
Scan edges P2: 29.999.99MHz
∂ F  Span: ±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANSELECTSELECT EXITEXIT
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
 MEMORY SCAN
14.195.00
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO
VFOVFO
1212