Icom IC-756 - Select Memory Scan and Settings

50
6
SCANS
q If the start up screen is not selected (if [F-5]’s func-
tion is [EXIT]), push [F-5] one or more times to exit.
w Select memory mode.
e Select the desired operating mode.
- The operating mode can also be changed while scan-
ning.
r Push [(F-4)SCAN] to select the scan screen.
t Set [RF/SQL] open or closed.
- See p. 47 for scan condition.
- If the [RF/SQL] control function is set as RF control, the
squelch always opens. See pgs. 2, 56 for details.
y Push [(F-1)MEMORY] to start the memory scan.
- Decimal points blink while scanning.
u Push [(F-3)SELECT] to start select memory scan;
push [(F-3)SELECT] again to return to memory
scan, if desired.
i When the scan detects a signal, the scan stops,
pauses or ignores it depending on the resume set-
ting and the squelch condition.
o To cancel the scan, push [
(F-1)MEMORY].
NOTE: 2 or more memory channels must be des-
ignated as select memory channels for select
memory scan to start.
■ Select memory scan operation
2.4k2.4k9 2.8k2.8k455455
12:3412:34
Programmed P1:0.500.00MHz
Scan edges P2: 29.999.99MHz
∂ F  Span: ±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANSELECTSELECT EXITEXITMEMORYMEMORY
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
VFOVFO
14.195.00
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO
1212
MEMORYMEMORY
2.4k2.4k9 2.8k2.8k455455
12:3412:34
Programmed P1:0.500.00MHz
Scan edges P2: 29.999.99MHz
∂ F  Span: ±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANSELECTSELECT EXITEXIT
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
 SELECT MEMORY SCAN
14.195.00
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO
VFOVFO
1212
q If the start up screen is not selected (if [F-5]’s func-
tion is [EXIT]), push [F-5] one or more times to exit.
w Select memory mode.
e Push [(F-4)SCAN] to select the scan screen.
r Select the desired memory channel to set as se-
lect memory channel.
t Push [(F-3)SELECT] to set the memory channel as
a select memory or not.
y Repeat steps r to t to program another memory
channel as a select memory channel, if desired.
u Push [
(F-5)EXIT] to exit the scan screen.
NOTE: Select memory channels can also be set in
the memory channel screen. (p. 42)
■ Setting select memory channels
2.4k2.4k9 2.8k2.8k455455
12:3412:34
Programmed P1:0.500.00MHz
Scan edges P2: 29.999.99MHz
∂ F  Span: ±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANSELECTSELECT EXITEXITMEMORYMEMORY
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
VFOVFO
14.195.00
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO
1212
2.4k2.4k9 2.8k2.8k455455
12:3412:34
Programmed P1:0.500.00MHz
Scan edges P2: 29.999.99MHz
∂ F  Span: ±10kHz
[SCAN][SCAN]
∂F ∂FSPANFSPANSELECTSELECT EXITEXITMEMORYMEMORY
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
OFFOFF
ATTATT
OFFOFF
AGCAGC
MIDMID
VFOVFO
14.195.00
USBUSB
USBUSB
14.100.0014.100.00
1ß
14.100.0014.100.00
14.205.0014.205.00
USBUSB
USBUSB
TX
VFOVFO
1212
ß
“ß” appears for select memory channels.