Icom IC-756PROIII - Page 117

112
16
CONTROL COMMAND
•Command table (continued)
1A 0517 Send/read power-ON timer set
(0000 to 2359)
0518 Send/read power-OFF period
(5=5 min. to 120=120 min. in
5 min. step)
0519 Send/read calibration marker
(0=OFF, 1=ON)
0520 Send/read confirmation beep
(0=OFF, 1=ON)
0521 Send/read band edge beep
(0=OFF, 1=ON)
0522 Send/read RF/SQL control set
(0=Auto, 1=SQL, 2=RF+SQL)
0523 Send/read quick dualwatch set
(0=OFF, 1=ON)
0524 Send/read quick split set (0=OFF,
1=ON)
0525 Send/read FM split offset (HF)
–4.000 to +4.000 MHz
(see p. 114 for details)
0526 Send/read FM split offset (50 MHz)
–4.000 to +4.000 MHz
(see p. 114 for details)
0527 Send/read split lock set (0=OFF,
1=ON)
0528 Send/read tuner auto start set
(0=OFF, 1=ON)
0529 Send/read PTT tune set (0=OFF,
1=ON)
0530 Send/read antenna selection
(0=OFF, 1=Manual, 2=Auto)
0531 Send/read RTTY mark frequency
(0=1275 Hz, 1=1615 Hz,
2=2125 Hz)
0532 Send/read RTTY shift width
(0=170 Hz, 1=200 Hz, 2=425 Hz)
0533 Send/read RTTY keying polarity
(0=Normal, 1=Reverse)
0534 Send/read RTTY decode USOS
(0=OFF, 1=ON)
0535 Send/read RTTY decode new line
code (0=CR,LF,CR+LF,
1=CR+LF)
0536 Send/read speech language
(0=English, 1=Japanese)
0537 Send/read speech speed (0=slow,
1=fast)
0538 Send/read S-level speech (0=OFF,
1=ON)
0539 Send/read memo pad numbers
(0=5 ch, 1=10 ch)
0540 Send/read main dial auto TS
(0=OFF, 1=Low, 2=High)
0541 Send/read mic. up/down speed
(0=Low, 1=High)
0542 Send/read CI-V transceive set
(0=OFF, 1=ON)
0543 Send/read CI-V 731 mode set
(0=OFF, 1=ON)
16 22 Noise blanker (0=OFF; 1=ON)
40 Noise reduction (0=OFF; 1=ON)
41 Auto notch (0=OFF; 1=ON)
42 Repeater tone (0=OFF; 1=ON)
43 Tone squelch (0=OFF; 1=ON)
44
Speech compressor (0=OFF; 1=ON)
45 Monitor (0=OFF; 1=ON)
46 VOX function (0=OFF; 1=ON)
47 Break-in (0=OFF; 1=semi break-
in; 2=full break-in)
48 Manual notch (0=OFF; 1=ON)
49 RTTY filter (0=OFF; 1=ON)
4F Twin peak filter (0=OFF; 1=ON)
50 Dial lock (0=OFF; 1=ON)
19 00 Read the transceiver ID
1A 00 Send/read memory contents (see
p. 114 for details)
01 Send/read band stacking register
contents (see p. 114 for details)
02 Send/read memory keyer con-
tents (see p. 114 for details)
03 Send/read the selected filter width
(0=50 Hz to 40/31=3600/2700 Hz)
04 Send/read the selected AGC time
constant (0=OFF, 1=0.1/0.3 sec. to
13=6.0/8.0 sec.)
0501 Send/read SSB TX Tone (Bass)
level (0 =min. to 10=max.)
0502 Send/read SSB TX Tone (Treble)
level (0=min. to 10=max.)
0503 Send/read MONITOR gain (0=min.
to 255=max.)
0504 Send/read CW side tone gain
(0=min. to 255=max.)
0505 Send/read CW side tone gain limit
(0=OFF, 1=ON)
0506 Send/read beep gain (0=min. to
255=max.)
0507 Send/read beep gain limit (0=OFF,
1=ON)
0508 Send/read LCD contrast (0=0% to
255=100%)
0509 Send/read LCD backlight (0=0% to
255=100%)
0510 Send/read LCD horizontal position
(0=1 to 7=8)
0511 Send/read switch backlight (0=1 to
7=8)
0512 Send/read display type (0=A, 1=B,
2=C, 3=D, 4=E, 5=F, 6=G, 7=H)
0513 Send/read display font (0=Basic1,
1=Basic2, 2=Pop, 3=7seg,
4=Italic1, 5=italic2, 6=Classic)
0514 Send/read memory name (0=OFF,
1=ON)
0515 Send/read my call setting (10-char-
acter: see p. 114)
0516 Send/read current time (0000 to
2359)
Command Sub command Description Command Sub command Description
16