Icom IC-756PROIII - Board Layouts Continuation; PA UNIT (BOTTOM VIEW)

84
9
SCANS
9
■ Programmed scan operation
q Push [EXIT/SET] several times to close a multi-
function screen, if necessary.
w Select VFO mode.
e Select the desired operating mode.
•The operating mode can also be changed while scan-
ning.
r Push [(F-5)SCAN] to select the scan screen.
t Set [RF/SQL] open or closed.
• See previous page for scan condition.
•If the [RF/SQL] control function is set as “AUTO,” the
squelch is always open in SSB, CW and RTTY modes.
See pgs. 2, 30, 99 for details.
y Push [(F-1)PROG] to start the programmed scan.
• Decimal points blink while scanning.
u When the scan detects a signal, the scan stops,
pauses or ignores it depending on the resume set-
ting and the squelch condition.
i To cancel the scan, push [(F-1)PROG].
If the same frequencies are programmed into the
scan edge memory channel P1 and P2, pro-
grammed scan does not start.
SFT
SFT
0
FIL2
FIL2
USB
USB
TX
TX
VFO
VFO
USB
USB
USB
USB
USB
USB
FIL2
FIL2
qr.qot.pp
qr.wpt.pp
14.100.00
14.100.00
14.100.00
14.100.00
1
1
VFO
VFO
BW
BW
2.4k
2.4k
SCAN
SCAN
ANT
1
COMP
COMP
OFF
WIDE
WIDE
METER
METER
Po
P.AMP
P.AMP
1
AGC
AGC
MID
MID
ATT
ATT
OFF
OFF
VOX
VOX
OFF
OFF
PROG
PROG
∂
F FINE
FINE
∂
F SPAN
F SPAN
SET
SET
qw:pp
12:00
PROGRAM SCAN
PROGRAM SCAN
∂ F  Span
Span


: ±
±
10kHz
10kHz
Programmed
Programmed
 P1:
P1:


0.500.00MHz
0.500.00MHz
scan
scan
 edges
edges
 P2:
P2:
 29.999.99MHz
29.999.99MHz
PROG
PROG
∂
F FINE
FINE
∂
F SPAN
F SPAN
SET
SET
SCAN
SCAN
COMP
COMP
OFF
OFF
WIDE
WIDE
AGC
AGC
MID
MID
VOX
VOX
OFF
OFF
∂ F  Span
Span


: ±
±
10kHz
10kHz
Programmed
Programmed
 P1:
P1:


0.500.00MHz
0.500.00MHz
scan
scan
 edges
edges
 P2:
P2:
 29.999.99MHz
29.999.99MHz
■
∂∂
F scan operation
q Push [EXIT/SET] several times to close a multi-
function screen, if necessary.
w Select VFO mode or a memory channel.
e Select the desired operating mode.
•The operating mode can also be changed while scan-
ning.
r Push [(F-5)SCAN] to select the scan screen.
t Set [RF/SQL] open or closed.
• See previous page for scan condition.
•If the [RF/SQL] control function is set as “AUTO,” the
squelch is always open in SSB, CW and RTTY modes.
See pgs. 2, 30, 99 for details.
y Set the ∂F span by pushing [(F-4)
∂∂
F SPAN].
•±5 kHz, ±10 kHz, ±20 kHz, ±50 kHz, ±100 kHz,
±500 kHz and ±1000 kHz are selectable.
u Set center frequency of the ∂F span.
i Push [(F-2)
∂∂
F] to start the ∂F scan.
• Decimal points blink while scanning.
o When the scan detects a signal, the scan stops,
pauses or ignores it depending on the resume set-
ting and the squelch condition.
!0 To cancel the scan, push [(F-2)
∂∂
F].
SFTSFT
0
FIL2FIL2
USBUSB
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr.qot.pp
qr.wpt.pp
14.100.0014.100.00
14.100.0014.100.00
1
1
VFOVFO
BWBW
2.4k2.4k
SCANSCAN
ANT
1
COMPCOMP
OFF
WIDEWIDE
METERMETER
Po
P.AMPP.AMP
1
AGCAGC
MIDMID
ATTATT
OFFOFF
VOXVOX
OFFOFF
PROGPROG
∂
F FINEFINE
∂
F SPANF SPAN
SETSET
qw:pp
12:00
∂ F  SCANSCAN
∂ F  CenterCenter:  14.195.00MHz14.195.00MHz
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz
PROGPROG
∂
F FINEFINE
∂
F SPANF SPAN
SETSET
SCANSCAN
COMPCOMP
OFFOFF
WIDEWIDE
AGCAGC
MIDMID
VOXVOX
OFFOFF
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz