Icom IC-M506 Service Manual (English)

Other manuals for Icom IC-M506

Service Manual45 pages

Specifications4 pages

Questions and Answers:

L
Laura NicholsAug 17, 2025
What to do if there is no sound from my Icom Transceiver speaker?
- K
  Kendra HornAug 17, 2025
  If you experience little or no sound from your Icom Transceiver speaker, there are several possible reasons. First, the squelch level may be set too high; in this case, set the squelch to the threshold point. Second, the volume level could be set too low; adjust the volume to a suitable level. Finally, if the speaker has been exposed to water, try removing the water using the earthquake function.
S
Scott WilliamsAug 19, 2025
Why is transmitting impossible or high power not selectable on my Icom Transceiver?
- D
  Daisy GrahamAug 19, 2025
  If transmitting is impossible or high power cannot be selected on your Icom Transceiver, it could be due to a couple of reasons. Some channels may be programmed for low power or receive only due to regulations; try changing channels. Alternatively, the output power might be set to low; push the power button to select high power.
M
Mark WhiteAug 22, 2025
How to fix Icom Transceiver that does not turn on?
- B
  Brenda HouseAug 22, 2025
  If your Icom Transceiver does not turn on, check the connection to the transceiver and power supply.
A
Adam WalkerAug 25, 2025
How to enable beep sounds on Icom IC-M506?
- H
  hineskennethAug 26, 2025
  If you are not hearing any beep sounds on your Icom Transceiver, the beep tones may be turned off. To resolve this, turn the beep tones on in the configuration menu.
F
Francis JonesAug 27, 2025
What to do if scan does not start on Icom IC-M506 Transceiver?
- R
  Rodney WalkerAug 28, 2025
  If the scan function does not start on your Icom Transceiver, it may be because favorite channels are not programmed. To fix this, set the desired channels as favorite channels.
L
Laura KnappAug 30, 2025
Why distress calls cannot be transmitted on Icom Transceiver?
- C
  cardenasamandaAug 30, 2025
  If distress calls cannot be transmitted on your Icom Transceiver, the DCS SELF ID code may not be programmed. Program the DCS SELF ID code to resolve this issue.
R
Robert MartinezSep 2, 2025
Why is there little or no sound coming from my Icom IC-M506 speaker?
- Q
  qsharpSep 2, 2025
  If you're getting little or no sound from your Icom Transceiver's speaker, the squelch level might be set too high. Try setting the squelch to the threshold point. Also, ensure the volume level isn't too low by adjusting it to a suitable level. If the speaker has been exposed to water, use the AquaQuake function to remove it.
D
dale80Sep 5, 2025
What to do if transmitting is impossible on Icom Transceiver?
- W
  whitakertroySep 5, 2025
  If you cannot transmit or select high power on your Icom Transceiver, it might be because some channels are programmed for low power or receive only due to regulations. Try changing channels. Alternatively, the output power might be set to low; push the [HI/LO] button to select high power.
D
Daniel StevensSep 8, 2025
Why does scan not start on my Icom IC-M506?
- D
  David CollinsSep 8, 2025
  If the scan does not start on your Icom Transceiver, it could be because fewer than two favorite channels are programmed. Set the desired channels as Favorite channels to resolve this.

Icom IC-M506 Specifications

General

Type	Marine VHF Transceiver
Frequency Range (Receive)	156.000 - 163.425 MHz
Waterproof Rating	IPX7
DSC	Yes
Output Power	25W
Weight	2.2 lbs
Display	Full Dot Matrix LCD
NMEA Connectivity	NMEA 0183