Icom MR-1000RII - 1 Panel Description; Front Panel

1
PANEL DESCRIPTION
1
■ Front panel
q POWER SWITCH [POWER]/[ ] (p. 7)
Push to turn the radar power ON or OFF.
• The standby screen appears for 90 seconds while the
magnetron warms up.
• The initial screen appears and a beep sounds after the
power has been turned ON.
w TRANSMIT/SAVE SWITCH [TX (SAVE)]/
[ ]
➥ Push to toggle between the TX mode and the
standby mode. (p. 8)
➥ Hold down for 1 second to turn ON the power
save function. The radar for TX interval scan is
fixed at 10 revolutions. (p. 11)
• Select the save time in INT. SETTING menu.
e RANGE UP/ DOWN SWITCHES [+]/[–]/
[ ]/[ ] (p. 8)
Push [+] to increase the screen range.
Push [–] to decrease the screen range.
r UP, DOWN, LEFT, RIGHT KEYS [p] [q] [t] [u]
Set the EBLs, VRMs, alarm area, ATA target, etc.
according to the key pushed.
Use [p] [q] to select menu item and [t] [u] to set
the item.
Using [p] [t]/[p] [u] or [q] [t]/[q] [u] combina-
tion allows you to move the cross line cursor to the
upper (or lower) left or right.
t TRAILS SWITCH [TRAILS]/[
] (p. 11)
Push to toggle the trail function ON or OFF. This is
useful for watching other ship’s tracks, approximate
relative speed.
• Trail Time can be set in VIDEO menu.
y ZOOM FUNCTION [ZOOM]/[ ] (p. 10)
Push [TARGET]/[ ] and [TRAILS]/[ ] si-
multaneously to toggle the ZOOM function ON or
OFF. The ZOOM function enlarges the target to two
times normal size.
• Move the cursor to the target, then turn ON the function.
• The screen zooms the middle of the screen around own
ship.
• This function is not available on the
1
⁄8 and the 32 NM or
higher ranges.
u MODE SWITCH [MODE]/[ ]
Push to select the Head-up (H UP), Course-up (C
UP), North-up (N UP) or True motion (TM) screens.
• The North-up and Course-up screens can be selected
only when a bearing data input is connected. (p. 38)
• The TM screen requires bearing data and LOG or posi-
tion data. (p. 38)
• TheTM screen is not selectable on the 32 NM or higher
range.
i OFF CENTER FUNCTION [OFF CENT]/[ ]
(p. 9)
Push [ALM]/[ ] and [MODE]/[ ] simulta-
neously to turn the OFF CENTER function ON or
OFF.
• This function is usable on 24NM or less ranges.
MOB
GAIN
SEA
RAIN
POWER
TX
SAVE
TARGET TRAILS
ZOOM
ALM
MODE
OFF CENT
EBL1
VRM1
PI
BRILL MENU
HL OFF
EBL2
VRM2
MARINE RADAR
TX
SAVE
TARGET TRAILS
MODEALM
+
-
MOB
MENU
EBL2
VRM2
EBL1
VRM1
BRILL
ZOOM
OFF CENT
PI
HL OFF
GAIN
SEA
RAIN
POWER
e
r
q
w
t
u
o
!1
y
i
!2
!3
!4
!5
!6
!7
!8
!9
@0
e
r
q
w
t
u
o
!1
y
i
!2
!3
!4
!5
!6
!7
!8
!9
@0
!0 !0
Control panel (English) Control panel (Chinese)