ICS Nav6 - User Manual

Other manuals for ICS Nav6

Manual5 pages

Questions and Answers

M
Matthew LindseyAug 19, 2025
Why does my ICS Ranges display SIG on the status line?
- C
  Christina HarrisSep 12, 2025
  If the status line on your ICS Ranges shows 'SIG,' indicating a signal fault, it might be due to NAVTEX stations transmitting carrier without modulation or local interference. If it appears briefly, it's usually not a concern. However, if it persists, investigate potential receiver errors or interference from nearby equipment. Try turning off devices like battery chargers one by one to identify the source of the interference.
J
James WestAug 21, 2025
What to do if ICS Ranges LCD is blank and RED LED is off?
- D
  Derek WallAug 21, 2025
  If your ICS Ranges LCD is blank and the RED LED is off, it indicates a power issue. Ensure that 12V is correctly connected to the RED wire and 0V is connected to its BLACK pair.
F
fjonesAug 23, 2025
How to fix a blank LCD screen with a red LED on ICS Ranges?
- K
  kingmadelineAug 25, 2025
  If your ICS Ranges LCD is blank but the RED LED is on, it could be due to the green wire being incorrectly connected to 12V. Disconnect the green wire, as it should only be connected for programming purposes.
K
Kelly MitchellAug 26, 2025
What to do if my ICS Ranges receive no NAVTEX messages?
- B
  barrettanthonyAug 26, 2025
  If you are not receiving NAVTEX messages on your ICS Ranges, first ensure that you are within the range of a NAVTEX station. Then, verify that a NAVTEX channel is selected. Also, check the message age limit setting and decrease it to bring older messages into view. Look for 'SIG' or 'ERR' on the status line. If there is no error icon, refer to Appendix II.
R
Robert DavisAug 28, 2025
Why is there no 518 or 490 icon on my ICS Ranges status line?
- R
  Robert RodriguezAug 28, 2025
  If the 518 or 490 icon is missing from the status line on your ICS Ranges, make sure that one or both NAVTEX channels are selected. If you cannot select a channel, it indicates that the sensor is unavailable; in this case, refer to ERR troubleshooting.
S
sandrashortAug 30, 2025
Why is there no GPS indicator on my ICS GPS status line?
- G
  Gregory BakerAug 30, 2025
  If there's no GPS indicator showing on the status line of your ICS GPS unit, the issue might stem from a lack of NMEA data input. First, verify the NMEA data connections. Then, ensure that the GPS unit is powered on and configured to output compatible NMEA sentences.
B
Benjamin EdwardsSep 1, 2025
What to do if ERR appears on ICS GPS status line?
- G
  Gregg KaufmanSep 1, 2025
  If you see 'ERR' on the status line of your ICS GPS, it indicates a communications error. This could be due to several reasons: * **No power to Sensor:** Verify the connections to the sensor and check for 12V between the YELLOW wire and its BLACK pair. * **No communications to Sensor:** Again, check the sensor connections and voltage as above. * **Display Mode set to “Slave”:** For single display systems, ensure the ‘Display Mode’ is set to “Master”. * **Two or more master displays connected to a sensor:** Configure one display as the master and the others as slaves.
B
Breanna PrestonSep 4, 2025
Why is the RED LED flashing on my ICS GPS every 15 seconds?
- K
  Kelly GeorgeSep 4, 2025
  If the RED LED on your ICS GPS is flashing every 15 seconds and the display isn't working, the device is likely in Sleep Mode. To wake it up, simply press any key to activate the display.
C
Cassidy MooreSep 6, 2025
What to do if the LCD is blank and the RED LED is off on my ICS GPS?
- A
  Andrew ClarkeSep 6, 2025
  If the LCD screen on your ICS GPS is blank and the RED LED is off, it likely indicates a power issue. Check that 12V is properly connected to the RED wire and that 0V is connected to its BLACK pair.
J
Justin BishopSep 8, 2025
Why is the RED LED flashing every 2 seconds on my ICS GPS?
- M
  michaelareedSep 8, 2025
  If the RED LED on your ICS GPS is flashing every 2 seconds and the display is not operating, it means the display unit isn't getting enough voltage.