Home
IEI Technology
Control Panel
MiniMax 3
IEI Technology MiniMax 3 User Manual
4
of 1
of 1 rating
48 pages
Give review
Manual
Specs
To Next Page
To Next Page
Loading...
IEI MiniMax 3
Installation/Programming Manu
al
Document Number: 6055672
Revision: 1.0
Date: 01/23/07
2
Table of Contents
Default Chapter
2
Table of Contents
2
Section 1: System Features and Specifications
5
System Features
5
Table 1: System Features
5
Specifications
6
System Defaults
6
Table 2: Specifications
6
Table 3: System Defaults
6
Max 3 Door Control Module Diagram
7
Figure 1: Max 3 Module Diagram
7
Backplane Diagram
8
Figure 2: Minimax 3 Backplane Diagram
8
Section 2: Installation
9
Check the Packing List
9
Mount the Enclosure
9
Ground the Unit
10
Figure 3: Connecting the GND Terminal from Transformer to the Backplane
10
Connect the RS-485 Cable from the Module to the Backplane
11
Figure 4: RS-485 Connection from Max 3 Module to Backplane
11
Wire an Electric Door Lock to the Main Relay of the Max 3 Module
12
Installing a Diode to Prevent Electrical Kickback from Lock - DC Locks Only
13
Installing an MOV to Prevent Electrical Kickback from Lock - AC Locks Only
13
Figure 5: Connecting Diode Across Strike
13
Figure 6: Connecting Diode Across Maglock
13
Figure 7: Connecting MOV Across Strike
13
Connect a Secured Series Front End (SSFE) Reader to the Door Control Module
14
Figure 8: Connect Secured Series Front End to DCM
14
Connect the Primary Wiegand Front End Reader (in Reader)
15
Figure 9: Connect Primary Wiegand Front End Reader to DCM
15
Connecting a Secondary Wiegand Front End Reader (out Reader)
16
Figure 10: Connect Secondary Wiegand Front End Reader to DCM
16
Wire a Request to Exit (REX) Device and Door Contact
17
Figure 11: Wiring a REX Switch and Door Contacts
17
Wire the Alarm Shunt Relay
18
Figure 12: Wiring the Alarm Shunt Relay
18
Wire the Door Ajar Relay
19
Figure 13: Wiring the Door Ajar Relay
19
Wire the Forced Door Relay
20
Figure 14: Wiring the Forced Door Relay
20
Network the Minimax 3
21
Connect the Minimax 3 Backplane Directly to a PC
21
Figure 15: Wiring Minimax 3 Backplane to a PC
21
Connect Multiple Backplanes Together
22
Figure 16: Connecting Multiple Backplanes Together
22
Connect the SEG-M to the Minimax 3 (LAN/WAN Connection)
23
Figure 17: Connecting the SEG-M to the Minimax 3
23
Connecting the SEG-1 to the Minimax 3 (LAN/WAN Connection)
24
Figure 18: Connecting the SEG-1 to the Minimax 3
24
Installing a Tamper Switch
25
Figure 19: Installing a Tamper Switch
25
Complete Connections between the 16.5 VAC Transformer and Backplane
26
Figure 20: Completing the Transformer Connections
26
Power up the System
27
Section 3: Programming
28
Programming Methods
28
Figure 21: Plug on Detachable Keypad
28
Entering Program Mode and Changing the Master Code
29
Entering Program Mode
29
Changing the Master Code
29
Programming a Supervisor Code
29
Changing the Door Number
30
Changing the Main Relay Time
30
Setting the Time and Date
30
Programming Users
31
User Types
31
Table 4: User Types
31
Programming a "Code Only" User
32
Programming "Card Only" Users by Presentation
32
Programming 26-Bit "Card Only" Users Without Presentation
32
Programming "Code and Card" Users
33
Programming "Code or Card" Users
33
Programming 26-Bit "Card Only" Users Via Batch Entry Without Presentation
33
Programming Consecutive "Card Only" Users Via Batch Entry by Presentation
34
Command 50 Quick Program Feature - "Code Only" or "Card Only
34
Deleting Users
35
Delete a Single User
35
Delete a Block of Users
35
Programming Extended Unlock Time
36
Programming Facility Code
36
Programming User Lockout
36
Programming the Door Ajar Output Time
37
Programming the Forced Door Time
37
Using the Default Auto-Unlock Timezone
38
Enable/Disable Timezones
38
Enable/Disable Auto-Unlock
38
Enable/Disable First-In Auto-Unlock
38
Programming Error Lockout
39
Setting the Error Lockout Threshold
39
Setting the Error Lockout Duration
39
Programming Wiegand LED Active State
39
Programming Wiegand Sounder Active State
40
Enable/Disable Control Module Audio Indicators
40
Table 5: Control Module Audio Indicators
40
Reseting System Defaults and Erasing Memory
41
Resetting the Master Code and System Defaults Only
41
Erasing Entire Memory/Resetting System Defaults
41
Erasing the Transaction Event Log
41
Programming Daylight Savings Time
42
Enabling/Disabling Daylight Savings Time
42
Selecting Daylight Savings Time Format
42
Programming Options Chart
43
Table 6: Programming Options Chart
43
Section 4: Troubleshooting
46
Troubleshooting Chart
46
Keypad Self-Test
46
Front End Error Indicators
46
Table 7: Troubleshooting Chart
46
Table 8: Front End Error Indicators
46
Lithium Battery Replacement
47
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the IEI Technology MiniMax 3 and is the answer not in the manual?
Ask a question
IEI Technology MiniMax 3 Specifications
General
Brand
IEI Technology
Model
MiniMax 3
Category
Control Panel
Language
English
Need help?
General
To Next Page