20
TROUBLESHOOTING
POWER
The unit will not switch onThe unit will not switch on
The unit will not switch onThe unit will not switch on
The unit will not switch on
• Make sure that power cable is plugged into the
AC outlet.
• Unplug the power cable from AC outlet, wait for
five seconds or more, then plug the cable in
again.
SPEAKERS
No sound is heard from the speakersNo sound is heard from the speakers
No sound is heard from the speakersNo sound is heard from the speakers
No sound is heard from the speakers
• Make sure the speakers are connected correctly
and the speaker cables’ core wires touch the
speaker connectors.
• Check to see if the volume level is set to
minimum.
• If the MUTING indicator is flashing, the sound is
muted. Cancel the muting function.
FM/AM TUNER
Noise is heard during broadcast, or too much white noiseNoise is heard during broadcast, or too much white noise
Noise is heard during broadcast, or too much white noiseNoise is heard during broadcast, or too much white noise
Noise is heard during broadcast, or too much white noise
is heard during an FM stereo broadcastis heard during an FM stereo broadcast
is heard during an FM stereo broadcastis heard during an FM stereo broadcast
is heard during an FM stereo broadcast
• Change the location of the antenna.
• Locate the unit further from the TV or computer.
• Driving cars nearby or flying aeroplanes could
cause noise.
• The broadcasting radio signal may be weak if a
concrete wall obstructs the signal path .
• Try setting FM mode to Mono.
• Noise may be heard when you operate the
remote control during AM reception.
• If nothing can improve the reception, install an
outdoor antenna.
REMOTE CONTROL
The remote control does not function correctlyThe remote control does not function correctly
The remote control does not function correctlyThe remote control does not function correctly
The remote control does not function correctly
• Make sure that the batteries have been installed
with the correct polarity.
• Replace both batteries with new ones (Do not
mix different types of batteries or new and old
batteries).
• The distance between the remote control and
the remote control sensor may be too far. Or,
there may be an object between them.
• The remote control sensor on the unit may be
receiving a strong beam of light (inverter
fluorescent light or sunlight).
• Make sure to use the same REMOTE ID code both
for the remote control and NP200.
TIMER/ALARM
Timer playback does not workTimer playback does not work
Timer playback does not workTimer playback does not work
Timer playback does not work
• The clock must be set correctly. If the clock is not
set, timer playback does not work. Make sure you
program the current day and time.
• If you selected
Server Server
Server Server
Server or
iNetRadioiNetRadio
iNetRadioiNetRadio
iNetRadio and the media
is not available (for example, if the SoundServer
is in standby), the NP200 will automatically use
FM/AM radio as the alarm source.
ETHERNET NETWORK
The unit fails to activate the Internet radio or musicThe unit fails to activate the Internet radio or music
The unit fails to activate the Internet radio or musicThe unit fails to activate the Internet radio or music
The unit fails to activate the Internet radio or music
server featureserver feature
server featureserver feature
server feature
Your network is either not connected properly or not
configured properly.
• Check the connection between this unit and the
LAN side port of your router (gateway) .
• Make sure that the modem and router (gateway)
are correctly connected. Also, make sure that the
power is on.
The unit fails to obtain a station list from the InternetThe unit fails to obtain a station list from the Internet
The unit fails to obtain a station list from the InternetThe unit fails to obtain a station list from the Internet
The unit fails to obtain a station list from the Internet
The radio site is out of service or otherwise inaccessible
due to some other reason such as maintenance.
• Try to access the site after a while.
Selecting the Music Server source fails to play music orSelecting the Music Server source fails to play music or
Selecting the Music Server source fails to play music orSelecting the Music Server source fails to play music or
Selecting the Music Server source fails to play music or
fails to connect to the SoundServerfails to connect to the SoundServer
fails to connect to the SoundServerfails to connect to the SoundServer
fails to connect to the SoundServer
Your SoundServer is not turned on.
• Turn on your SoundServer.
No audio files on the SoundServer.
• Record CDs onto your SoundServer.
To Next Page
Loading...