19
5.1 Surround Sound Receiver
www.insigniaproducts.com
To select a surround mode:
• Rotate the SURROUND/STEREO knob on the
front of your receiver. Each time you rotate the
knob, the surround mode changes:
• AUTO—The truest surround sound is
selected automatically based on the
number of channels in the input signal.
AUTO lights on the display.
• MANUAL—Lets you select the surround
mode manually based on the input signal.
AUTO disappears from the display
Or,
• Press SURROUND or SURROUND to
select a surround mode, or press STEREO to
select a stereo mode.
Adjusting sound parameters
To adjust sound parameters:
1 Press SOUND PARAMETER. The currently
selected parameter, such as EQ : ~ or L.SYNC : ~,
appears on the display. If the parameter
disappears, press SOUND PAPAMETER again.
2 Press TUNE or TUNE to select a parameter.
Each time you press one of these buttons the
parameter changes in the following sequence:
• EQ—(Room EQ). The room EQ is a kind of
room equalizer for your speakers. According to
the acoustic characteristics of your room
measured by the ROOM EQ setup, the room
EQ automatically adjusts the frequency
response of your speakers.
If you use different brands or sizes of speakers
for some channels or have a room with unique
acoustic characteristics, such as walls,
furniture, and the dimensions or shape of the
room, we recommend using the room EQ.
• Select OFF to turn off the room EQ.
• Select ON to adjust the frequency
response of all speakers to the flattest
response.
• L.SYNC—(Lip-Sync). Some video devices
process the video signal later than the audio
signal. This may cause a slight time delay
between the video and audio signals. You can
use L.SYNC to adjust the time delay between
the video and audio. The adjustment range is
0.0 ~ 9.0 frames (1 second = 30 frames).
• DRC—(Dynamic Range Control). This function
compresses the dynamic range of previously
specified parts of Dolby Digital, Dolby TrueHD,
Dolby Digital Plus, DTS, DTS-HD High
Resolution Audio, or DTS-HD Master Audio
sound track (with extremely high volume) to
minimize the difference in volume between
the specified and non-specified parts. This
makes it easy to hear all of the sound track
when watching movies at night at low levels.
• Select AUTO to adjust the level of dynamic
range automatically. (Valid only when the
digital signals from the Dolby TrueHD
source are being input.)
• Select MAX to adjust it to maximum level.
• Select MID to adjust it to middle level.
• Select OFF to turn off the DRC function.
Input signal format Selectable surround/stereo mode
Dolby Digital Plus
Dolby TrueHD
AUTO SURROUND
corresponding DOLBY mode
STEREO
Dolby Digital 5.1 channel AUTO SURROUND
DOLBY DIGITAL
STEREO
Dolby Digital 2 channel AUTO SURROUND
DOLBY PLIIx MOVIE *
1
/DOLBY PLII MOVIE *
2
DOLBY PLIIx MUSIC *
1
/DOLBY PLII MUSIC *
2
DOLBY PLIIx GAME *
1
/DOLBY PLII GAME *
2
DOLBY PRO LOGIC
STEREO
DTS-HD high resolution audio
DTS-HD master audio
DTS
DTS 96/24
AUTO SURROUND
corresponding DTS mode
STEREO
PCM
Analog
AUTO SURROUND
DOLBY PLIIx MOVIE *
1
/DOLBY PLII MOVIE *
2
DOLBY PLIIx MUSIC *
1
/DOLBY PLII MUSIC *
2
DOLBY PLIIx GAME *
1
/DOLBY PLII GAME *
2
DOLBY PRO LOGIC
MOVIE
DRAMA
GAME
STADIUM
CLASSIC
HALL
7CH STEREO*
1
/5CH STEREO *
2
STEREO
Depending on the surround back speaker setting, the modes you can select vary:
*1— Possible only when surround back speaker is not set to NO
*2— Possible only when surround back speaker is set to NO
Note:
When the SPEAKER button is set to off, only the stereo mode can be selected.
Notes
• To set the EQ to ON, perform the ROOM EQ
setup first. For more information, see “Setting
the listening environment (ROOM EQ)” on
page 16.
• C.WIDTH, DIMEN, and PNRM can be selected
only while listening in Dolby Pro Logic II Music
mode or Dolby Pro Logic IIx Music mode.
→ EQ ↔ L.SYNC ↔ DRC ↔ LFE ←
→ PNRM ↔ DEMEN ↔ C.WIDTH ↔ A.DLY ↔ HDMI ←
To Next Page
Loading...
