Intermec SR61T1D

To Next Page

To Previous Page

Chapter 2 — Configuring Interface Settings

44 SR60 Scanner Programmer’s Reference Manual

Digits

0 ---------

1 ---------

2 ---------

3 ---------

4 ---------

5 ---------

Main Page

Table of Contents5
Before You Begin11
About Cautions and Notes11
Global Services and Support11
Warranty Information11
Web Support11
Telephone Support12
Who Should Read this Manual13
Related Documents13
Learning about Programming the SR60 Scanner15
What Is the SR6016
Customizing Your Scanner's Operation16
How to Program the SR60 Scanner17
What Is Programming Mode17
What Is a Programming Session17
Three Sample Programming Sequences19
Roadmap for Programming the Scanner21
About the Scanner Leds and Beeper21
Scanner Leds21
Scanner Beeper22
Integrating the Scanner with Your Host System22
Changing the Interface Cable23
Verifying that Your Scanner Supports the Interface23
Removing and Replacing the Scanner Interface Cable23
Reconfiguring the Interface Settings24
Restoring Factory Default Settings25
Trouble Scanning the Bar Codes in this Manual26
Contacting Intermec Product Support26
Configuring Interface Settings27
Wand Emulation Interface28
Wand Emulation Settings28
Wand Emulation Pre/Post-Noise Settings31
Keyboard Wedge Interface33
PC Keyboard Interface Selection33
Connect to a Laptop or PC and Send Control/Function Characters36
Caps Lock38
Country Mode39
Intercharacter Delay42
Quiet Interval43
RS-232 Communication Parameters45
Baud Rate45
Data Format Settings47
Handshaking49
Hardware Handshaking49
Software Handshaking51
RS-232 ACK/NAK Options53
RS-232 Intercharacter Delay54
USB Interface56
Configuring Label Transmit Settings61
When to Configure Label Transmit Settings62
How to Use the Prefix, Suffix, and Label ID62
Setting Global Prefixes and Suffixes63
Setting Global Prefixes63
Setting Global Suffixes64
Disabling a Global Prefix or Suffix66
Setting a Prefix or Suffix67
Setting a Prefix or Suffix for a USB Interface68
Setting an EOM for a USB Interface70
Setting a Prefix or Suffix for a Multi or Decoded Interface72
Setting a Label ID73
About Symbology-Specific Label Identifiers73
Setting the Label ID Location75
Setting a Symbology-Specific Label ID76
Selecting the Symbology77
Setting a Single-Character Label ID81
Disabling a Symbology-Specific Label ID82
Enabling and Configuring Symbologies83
All Symbologies Supported by All Interfaces84
Enabling Symbologies84
Code 39/Pharmacode 39 Options89
About Code 39 Options89
Check Digit89
Start/Stop Characters89
Code 39 Full ASCII89
Minimum Label Length89
Read Verification89
Code 39 Emulate Function Keys90
Configuring the Code 39 Options90
Minimum Label Length91
Read Verification94
Code 39 Emulate Function Keys95
About Pharmacode 39 Options96
Transmit Check Digit96
Start/Stop Characters96
Configuring the Pharmacode 39 Options96
Code 128 and UCC/EAN 128 Options97
About Code 128 and UCC/EAN 128 Options97
Setting Minimum Label Length97
Read Verification97
Configuring the Code 128/And UCC/EAN 128 Options98
Minimum Label Length98
Read Verification100
Interleaved 2 of 5 Options101
About Interleaved 2 of 5 Options101
Check Digit102
Label Length Format102
Read Verification103
Configuring the Interleaved 2 of 5 Options103
Label Length Format104
Variable Length Format104
Fixed Length Format105
Read Verification109
Codabar Options110
About Codabar Options110
Check Digit110
Gap Check110
Label Length Format110
Start/Stop Characters111
Start/Stop Match111
Start/Stop Format112
Read Verification112
Configuring the Codabar Options112
Label Length Format113
Variable Length Format113
Fixed Length Format114
Read Verification119
UPC/EAN Options120
About UPC/EAN Options120
Data Format Settings120
UPC/EAN Expansion120
UPC/EAN Add-Ons120
Price/Weight Check Digit121
Read Verification121
Configuring the UPC/EAN Options121
UPC Data Format Settings121
EAN Data Format Settings123
UPC/EAN Expansion124
UPC/EAN Add-Ons126
Custom Add-Ons128
Price/Weight Check Digit128
Read Verification129
Code 93 Options131
About Code 93 Options131
Minimum Label Length131
Read Verification131
Configuring the Code 93 Options132
Minimum Label Length132
Read Verification134
Standard 2 of 5/IATA Options135
About Standard 2 of 5/IATA Options135
Check Digit135
Label Length Format136
Read Verification137
Configuring the Standard 2 of 5/IATA Options137
Label Length Format138
Variable Length Format138
Fixed Length Format139
Read Verification142
IATA Options143
Msi/Plessey Options144
About Msi/Plessey Options144
Check Digit144
Label Length Format144
Read Verification145
Configuring the MSI /Plessey Options145
Label Length Format146
Variable Length Format146
Fixed Length Format147
Read Verification151
Configuring General Features153
Configuring the Green LED Idle State154
Configuring the Beeper Settings154
Configuring the Marker Beam158
Configuring the Low Power Mode160
Configuring the Low Power Shutdown Delay162
Configuring the Half Angle163
Factory Default Configuration165
Factory Default Configuration166
Reference Information171
Sample Bar Codes172
Keypad Bar Codes174
RS-232 Host Commands177
ASCII Character Set178

Intermec SR61T1D

Table of Contents

Other manuals for Intermec SR61T1D

Related product manuals