Jensen VM9313 User Manual (English)

Questions and Answers:

O
osotoSep 1, 2025
Why won't my Jensen Car Receiver play the disc?
- A
  April HansonSep 1, 2025
  If your Jensen Car Receiver won't play a disc, it could be due to several reasons: * The disc is warped or scratched: Use a disc in good condition. * The disc is dirty or wet: Clean the disc with a soft cloth. * The laser pickup is dirty: Clean the laser pickup with a cleaning disc. * An incompatible disc is used: Use a compatible disc. * The disc rating exceeds the Parental Lock rating limit: Change Parental Lock settings to lower restriction. * The disc region code is not compatible with the unit: Use a disc with the proper region code. * The disc is inserted upside down: Insert the disc with the label side up.
S
samantharamirezAug 30, 2025
What to do if there is no image on my Jensen Car Receiver?
- L
  Lisa ThompsonAug 30, 2025
  If there is no image on your Jensen Car Receiver, first check the wiring and correct any incorrect connections to the parking brake wire. Also, if PRK SW is activated, stop the vehicle in a safe place and apply the parking brake.
K
kjonesAug 29, 2025
Why is my Jensen Car Receiver having weak station searching?
- K
  kennethpierceAug 29, 2025
  Weak station searching on your Jensen Car Receiver can be due to a few reasons. The auto antenna may not be fully extended or properly connected; connect the auto antenna control cable properly. If you are trying to tune into an HD Radio broadcast that is too far away, change the tuning mode to “Analog”.
D
Dr. Heather Bailey DVMAug 27, 2025
What causes flashing images or interference on the Jensen Car Receiver screen?
- R
  richardskatieAug 27, 2025
  Flashing images or interference on the Jensen Car Receiver screen can occur if the DVD is not compatible with the current video system settings. Change the setup to accommodate the disc. It can also be caused by improper video signal connections, so check the wiring and correct it.
J
Joanne WilliamsAug 26, 2025
How to fix a Jensen Car Receiver remote control that is not working?
- H
  Hunter MorganAug 27, 2025
  If the remote control for your Jensen Car Receiver isn't working, the battery may be depleted. Replace the battery with a new one. Also, check if the battery is installed incorrectly; remove it and reinstall it correctly.
T
Travis RoseAug 25, 2025
Why is the sound quality poor or distorted on my Jensen Car Receiver?
- B
  Bradley GonzalezAug 26, 2025
  Poor sound quality or distortion on your Jensen Car Receiver could be due to several reasons. Using a pirated disc can cause this issue, so use an original copy. Also, ensure that the speaker power rating is compatible with the unit and connect proper speakers. Finally, check the speaker contact, as a shorted speaker can also lead to poor sound quality.
S
Suzanne WilliamsAug 23, 2025
What to do if there is no audio output from my Jensen Car Receiver?
- J
  Jordan WyattAug 23, 2025
  If you're experiencing no or low audio output from your Jensen Car Receiver, consider the following: * Check the wiring and correct any improper audio output connections. * Increase the volume level if it's set too low. * Review the wiring diagram and check the “MUTE” connection. * Replace any damaged speakers. * Adjust the channel balance to the center position if it's heavily biased. * Insulate all speaker wiring connections to prevent contact with metal parts of the car.

Jensen VM9313 Specifications

General

Screen Size	6.2 inches
Touchscreen	Yes
Radio Tuner	AM/FM
DVD Player	Yes
Navigation	No
Resolution	800 x 480
USB Port	Yes
SD Card Slot	Yes
Bluetooth	Yes
Auxiliary Input	Yes
Power Output	50W x 4
Peak Output	50W x 4
Audio Formats Supported	MP3, WMA
Preamp Outputs	3 (Front, Rear, Subwoofer)