JUKI LK-1900B series - Default Chapter; Table of Contents

i
CONTENTS
I. EXPLANATION OF LK-1900B,
COMPUTER-CONTROLLED HIGH-
SPEED BARTACKING MACHINE ........1
1. SPECIFICATIONS ..............................................1
2. CONFIGURATION .............................................2
2-1. Names of main unit ........................................... 2
2-2. Names and explanation of switches on the
operation panel .................................................. 3
3. INSTALLATION .................................................. 4
3-1. Installing the electrical box .............................. 4
3-2. Installing the pedal sensor ............................... 4
3-3. Attaching the connecting rod ........................... 5
3-4. Installing the head support rod ........................ 5
3-5. Installing and connecting the power switch ... 6
3-6. How to carry the sewing machine.................... 7
3-7. Installation of the sewing machine head......... 7
3-8. Installing the drain receiver and the head
support rubber ................................................... 8
3-9. Safety switch...................................................... 8
3-10. Tilting the sewing machine head ..................... 9
3-11. Installing the operation panel .......................... 9
3-12. Connecting the cords ..................................... 10
3-13. Handling the cords .......................................... 11
3-14. Installing the eye protection cover ................ 11
3-15. Installing the thread stand ............................. 12
3-16. In the case the machine is transported
after factory-completed at the time of
shipment .......................................................... 12
4. OPERATION OF THE SEWING MACHINE ..... 13
4-1. Lubrication ....................................................... 13
4-2. Attaching the needle ....................................... 13
4-3. Threading the machine head .......................... 14
4-4. Installing and removing the bobbin case ...... 14
4-5. Installing the bobbin ....................................... 15
4-6. Adjusting the thread tension .......................... 15
4-7. Adjusting the thread take-up spring .............. 16
4-8. Example of the thread tension ....................... 16
5. OPERATION OF THE SEWING MACHINE
(BASIC) ............................................................16
5-1. Selection of language ..................................... 16
5-2. Setting the pattern number ............................. 17
5-3. Setting the item data ....................................... 17
5-4. Checking the contour of a sewing pattern .... 20
5-5. Sewing .............................................................. 21
5-6. Changing the pattern to a different one ........ 21
5-7. Winding a bobbin ............................................ 22
5-8. Thread clamp device ....................................... 23
6. OPERATION OF THE SEWING MACHINE
(ADVANCED) ...................................................25
6-1. Performing sewing using the pattern keys .. 25
6-2. Sewing using the combination function
(cycle sewing) .................................................. 30
6-3. Sewing through the use of the counter ......... 33
6-4. How to use the temporary stop ...................... 36
6-5. Setting the pattern thread tension ................. 37
6-6. Copying or deleting various kinds of
pattern data ...................................................... 38
6-7. Communication ............................................... 40
6-8. Cautions in operation ...................................... 42
6-9. Setting enable/disable of standard pattern
invoking ............................................................ 43
7. MAINTENANCE ...............................................44
7-1. Adjusting the height of the needle bar .......... 44
7-2. Adjusting the needle-to-shuttle relation ........ 45
7-3. Adjusting the lift of the work clamp foot ....... 46
7-4. The moving knife and counter knife .............. 46
7-5. Needle thread clamp device ........................... 47
7-6. Adjustment of the wiper .................................. 47
7-7. Draining waste oil ............................................ 48
7-8. Amount of oil supplied to the hook ............... 48
7-9. Replacing the fuse........................................... 48
7-10. Replenishing the designated places with
grease ............................................................... 49
8. HOW TO USE THE MEMORY SWITCH .........51
8-1. Method of changing memory switch data ..... 51
8-2. List of the memory switch functions ............. 52
9. OTHERS ..........................................................56
9-1. Table of the standard pattern specications 56
9-2. Table of the standard patterns ....................... 57
9-3. Table of the work clamp foot .......................... 59
9-4. Installing the foot pedal switch (optional) ..... 61
9-5. Error list............................................................ 62
9-6. Message list ..................................................... 67
9-7. Troubles and corrective measures (sewing
conditions) ....................................................... 69
9-8. Table of the optional parts .............................. 71
II. EXPLANATION OF THE LK-1901B,
COMPUTER-CONTROLLED HIGH-
SPEED EYELET BUTTONHOLE
BARTACKING MACHINE ....................73
1. SPECIFICATIONS ............................................73
2. INSTALLATION OF THE SEWING
MACHINE AND PREPARATION OF THE
OPERATION ....................................................73
3. PREPARATION OF THE SEWING MACHINE 74
3-1. Adjustment of the material closing amount .. 74
3-2. Adjustment of the lift of the work clamp foot 74
3-3. Adjustment of the pressure of the work
clamp unit ........................................................ 75
3-4. Setting of the material closing operation ...... 75
4. OPERATION OF THE SEWING MACHINE ..... 76
4-1. Selection and conrmation of the sewing
patterns ............................................................ 76
III. EXPLANATION OF THE LK-1902B,
COMPUTER-CONTROLLED HIGH-
SPEED BELT-LOOP ATTACHING
MACHINE ............................................77
1. SPECIFICATIONS ............................................77
2. PREPARATION OF THE SEWING MACHINE 77
2-1. Threading the machine ................................... 77
3. OPERATION OF THE SEWING MACHINE ..... 78
3-1. Selection and conrmation of the sewing
patterns ............................................................ 78
3-2. Combination of the work clamp foot and
the feed plate ................................................... 78