Keysight N9030B - Page 2726

9 Programming the Instrument
9.1 List of Supported SCPI Commands
[:SENSe]:FREQuency:SPAN
[:SENSe]:FREQuency:SPAN:BANDwidth[:RESolution]:RATio
[:SENSe]:FREQuency:SPAN:BANDwidth[:RESolution]:RATio:AUTO
[:SENSe]:FREQuency:SPAN:FULL
[:SENSe]:FREQuency:SPAN:PREVious
[:SENSe]:FREQuency:STARt
[:SENSe]:FREQuency:STOP
[:SENSe]:FREQuency:SYNThesis:AUTO[:STATe]
[:SENSe]:FREQuency:SYNThesis[:STATe]
[:SENSe]:FREQuency:TUNE:IMMediate
[:SENSe]:FREQuency:TZOom:CENTer
[:SENSe]:FREQuency:TZOom:SPAN
[:SENSe]:FREQuency:TZOom:TIME:CENTer
[:SENSe]:FREQuency:ZSPan:CENTer
[:SENSe]:FREQuency:ZSPan:SPAN
[:SENSe]:HARMonics:AVERage:COUNt
[:SENSe]:HARMonics:AVERage[:STATe]
[:SENSe]:HARMonics:AVERage[:STATe]
[:SENSe]:HARMonics:AVERage:TCONtrol
[:SENSe]:HARMonics:BANDwidth|BWIDth[:RESolution]
[:SENSe]:HARMonics:BANDwidth|BWIDth[:RESolution]:AUTO
[:SENSe]:HARMonics:FREQuency:FUNDamental
[:SENSe]:HARMonics:FREQuency:FUNDamental:AUTO
[:SENSe]:HARMonics:FREQuency:STEP[:INCRement]
[:SENSe]:HARMonics:NUMBer
[:SENSe]:HARMonics:RTABle:FILL
[:SENSe]:HARMonics:RTABle:STATe
[:SENSe]:HARMonics:SWEeptime
[:SENSe]:HARMonics:SWEeptime:AUTO
[:SENSe]:HARMonics:SWEeptime:STATe
[:SENSe]:HARMonics:TONE[1]|2|…|10:BANDwidth|BWIDth[:RESolution]
[:SENSe]:HARMonics:TONE[1]|2|…|10:BANDwidth|BWIDth
[:RESolution]:AUTO
[:SENSe]:HARMonics:TONE[1]|2|…|10:FREQuency
[:SENSe]:HARMonics:TONE[1]|2|…|10:STATe
[:SENSe]:HARMonics:TONE[1]|2|…|10:SWEep:TIME
[:SENSe]:HARMonics:TONE[1]|2|…|10:SWEep:TIME:AUTO
[:SENSe]:HDUPlex:PORT:INPut
[:SENSe]:HDUPlex:PORT:OUTPut
[:SENSe]:IF:EDRange
[:SENSe]:IF:GAIN:FFT:AUTO[:STATe]
[:SENSe]:IF:GAIN:FFT[:STATe]
[:SENSe]:IF:GAIN:SWEPt:AUTO[:STATe]
[:SENSe]:IF:GAIN:SWEPt[:STATe]
[:SENSe]:LIST:ATTenuation
[:SENSe]:LIST:ATTenuation:POINts?
[:SENSe]:LIST:BANDwidth|BWIDth:RESolution
[:SENSe]:LIST:BANDwidth|BWIDth:RESolution:POINts?
[:SENSe]:LIST:BANDwidth|BWIDth:RESolution:TYPE
[:SENSe]:LIST:BANDwidth|BWIDth:RESolution:TYPE:POINts?
Spectrum Analyzer Mode User's &Programmer's Reference 2726