112
Program operating mode
Page 5 - Pitch LFO2
The “LFO1 Intensity”, “JS+Y” and “AMS” settings will
be added to determine the depth and direction of the
pitch modulation applied by LFO1.
-12.00…+12.00
Parameter value.
PAGE 5 - PITCH LFO2
In this page you can set the LFO2 modulation parame-
ters for the selected oscillator. See “Page 4 - Pitch
LFO1” for information on the various parameters.
PAGE 6 - PITCH EG
Here you can make settings for the pitch EG, which cre-
ates time-variant changes in the pitch of the oscillators.
The depth of pitch change produced by these EG set-
tings on the oscillators is adjusted by the “Intensity
(AMS1/2 Intensity)” parameter (see page 112).
Pitch envelope
Start/Attack/Decay/Release Level
These parameters specify the amount of pitch change.
The actual amount of pitch change will depend on the
“Intensity (AMS1/2 Intensity)” parameter (see below).
For example, with an “Intensity” setting of +12.00, a
“Level” setting of +99 would raise the pitch one octave,
and a “Level” setting of –99 would lower the pitch one
octave.
-99…+99 Parameter value.
Start Level
Specifies the amount of pitch change at note-on.
Attack Level
Specifies the amount of pitch change when the attack
time has elapsed.
Release Level
Specifies the amount of pitch change when the release
time has elapsed.
Attack/Decay/Release Time
These parameters specify the time over which the pitch
change will occur.
0…99 Parameter value.
Attack Time
Specifies the time over which the pitch will change
from note-on until it reaches the pitch specified as the
attack level.
Decay Time
Specifies the time over which the pitch will change
after reaching the attack level until it reaches the nor-
mal pitch.
Release Time
Specifies the time over which the pitch will change
from note-off until it reaches the pitch specified as the
release level.
Pitch EG ‘Level’ modulation
AMS1/2 (L) (Alternate Modulation Source 1/2)
These parameters select the source that will control the
pitch EG “Level” parameters (“AMS (Alternate Modu-
lation Source) list” on page 124).
Intensity (AMS1/2 Intensity)
These parameters specify the depth and direction of
the effect applied by “AMS1”. With a setting of 0, the
levels specified by “Start/Attack/Decay/Release Level”
will be used.
For example if “AMS1” is Joystick +Y, pushing the joy-
stick to turn it on will change the “Level” parameters of
the Pitch EG. As the absolute value of “Intensity” is
increased, the pitch EG levels will change more greatly
when the joystick is released. The direction of the
change is specified by “Start Level Swing” and “Attack
Level Swing”. When the key pressure is released, the
pitch EG levels will return to their own settings.
If “AMS1” is set to Velocity, increasing the absolute value
of “Intensity” will produce increasingly wider change in
pitch EG levels for strongly-played notes. The direction
of the change is specified by “Start Level Swing” and
“Attack Level Swing”. As you play more softly, the pitch
change will draw closer to the pitch EG levels.
-99…+99 Parameter value.
Note-on
Note-off
Attack
Time
Decay
Time
Start Level
Release Level
Release Time
Attack Level
+99 = approximately 1 octave
–99 = approximately 1 octave
0 = pitch when
key is held
(sustained)
Time
Time-varying pitch settings (when Pitch EG Intensity = +12.00)
Pitch EG change (level) (AMS=JS-Y/Velocity, Intensity= positive (+) value
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
A note played softly with
Start Level Swing set at 0,
Attack Level Swing set to +,
the Joystick pulled on
A note played strongly with
Start Level Swing set to 0,
Attack Level Swing set to +,
the Joystick pulled on
A note played strongly with
Start Level Swing set to 0,
Attack Level Swing set to –,
the Joystick pulled on
To Next Page
Loading...
