224
084: Decim-Amp S
(Decimator – Amp Simulation)
This effect combines a mono-type decimator and an
amp simulation. You can change the order of the effect
connection.
085: Decim-Cmp
(Decimator – Compressor)
This effect combines a mono-type decimator and a
compressor. You can change the order of the effect con-
nection.
086: AmpS-Tremol
(Amp Simulation – Tremolo)
This effect combines a mono-type amp simulation and
a tremolo.
a
[D] Pre LPF Off, On
Turn the harmonic noise caused by lowered sampling on and off →Fx:014
High Damp [%]
Sets the ratio of high-range damping
0...100%
b
[D] Sampling Freq [Hz] (Sampling Frequency)
Sets the sampling frequency
1.00k...48.00kHz
Resolution
Sets the data bit length
4...24
→Fx:014
c
[D] Output Level
Sets the decimator output level
0...100
→Fx:014
d
[A] Amplifier Type
Selects the type of guitar amplifier
SS, EL84, 6L6
e
Routing DECI→AMP, AMP→DECI
Switches the order of the wah and amp simulation connection
f
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 177
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 177
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 177
–100...+100
a
[D] Pre LPF Off, On
Turn the harmonic noise caused by lowered sampling on and off
→Fx:014
High Damp [%]
Sets the ratio of high-range damping
0...100%
b
[D] Sampling Freq [Hz] (Sampling Frequency)
Sets the sampling frequency
1.00k...48.00kHz
Resolution
Sets the data bit length
4...24
→Fx:014
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Decimator
Routing
Pre LPF
High Damp
Output Level
Decimator
Resolution
Compressor
Comp
Output Level
Envelope - Control
c
[D] Output Level
Sets the decimator output level
0...100
→Fx:014
d
[C] Sensitivity
Sets the sensitivity
1...100
→Fx:002
e
[C] Attack
Table , “Sets the attack level,” on page 178
1...100
→Fx:002
Output Level
Sets the compressor output level
0...100
→Fx:002
f
Routing DECI→CMP, CMP→DECI
Switches the order of the decimator and compressor connection
g
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 177
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 177
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 177
–100...+100
a
[A] Amplifier Type
Selects the type of guitar amplifier
SS, EL84, 6L6
b
[T] LFO Waveform Triangle, Sine, Vintage, Up, Down
Selects LFO Waveform →Fx:032
LFO Shape –100...+100
Determines how much the LFO waveform is changed →Fx:020
c
[T] LFO Frequency [Hz]
Sets the LFO speed
0.02...20.00Hz
d
[T] Depth
Sets the depth of LFO modulation
0...100
e
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 177
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 177
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 177
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Amp Simulation Tremolo
Amp Simulation Filter
Tremolo
LFO: Tri/Sin/Vintage/Up/Down
LFO Shape
To Next Page
Loading...
