Launch X-431 IMMO PAD User Manual

LAUNCH
i
Trademarks
LAUNCH is a registered trademark of LAUNCH TECH CO., LTD. in China and other countries. All other
marks are trademarks or registered trademarks of their respective holders.
Copyright Information
Copyright © 2023 by LAUNCH TECH CO., LTD. (also called LAUNCH for short). All rights reserved. No
part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by
any means, electronic, mechanical, photocopying and recording or otherwise, without the prior written
permission.
Statement: LAUNCH owns the complete intellectual property rights for the software used by this product.
For any reverse engineering or cracking actions against the software, LAUNCH will block the use of this
product and reserve the right to pursue their legal liabilities.
Disclaimer of Warranties and Limitation of Liabilities
All information, illustrations, and specifications in this manual are based on the latest information
available at the time of publication.
The right is reserved to make changes at any time without notice. We shall not be liable for any direct,
special, incidental, indirect damages or any economic consequential damages (including the loss of
profits) due to the use of the document.
Important Safety Precautions
To avoid personal injury, property damage, or accidental damage to the product, read all of the
information in this section before using the tool.
DANGER
• When an engine is operating, keep the service area well-ventilated or attach a building exhaust
removal system to the engine exhaust system. Engines produce various poisonous compounds
(hydrocarbon, carbon monoxide, nitrogen oxides, etc.) that cause slower reaction time and result in
death or serious personal injury.
• Please use the included battery and power adaptor. Risk of explosion if the battery is replaced with an
incorrect type.
• DO NOT attempt to operate the tool while driving the vehicle. Have second personal operate the tool.
Any distraction may cause an accident.
WARNING
 Always perform automotive testing in a safe environment.
 Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
 Before starting the engine, put the gear lever in the Neutral position (for manual transmission) or in the
Park (for automatic transmission) position to avoid injury.
 NEVER smoke or allow a spark or flame in vicinity of battery or engine. Do not operate the tool in
explosive atmospheres, such as in the presence of flammable liquids, gases, or heavy dust.
 Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
 Wear an ANSI-approved eye shield when testing or repairing vehicles.
 Put blocks in front of the drive wheels and never leave the vehicle unattended while testing.

Launch X-431 IMMO PAD Specifications

General

RAM	4GB
Internal Storage	64GB
Operating System	Android
Resolution	1280 x 800
Processor	Quad-core
Connectivity	Wi-Fi, Bluetooth
Camera	5MP rear
Special Features	IMMO functions
Ports	USB

Summary

Important Safety Precautions

Product Introduction and Components

Product Profile Overview

Overview of the tablet-style diagnostic tool and its capabilities.

Package Contents List

Lists the items included in the product package for reference.

Display Tablet Details

Details the components and controls of the display tablet.

SmartLink C V2.0 Device

Explains the functions and applications of the SmartLink C V2.0 device.

Docking Station Functionality

Describes the function of the docking station for charging the diagnostic tablet.

Technical Specifications

Initial Setup Procedures

Charging the Diagnostic Tablet

Instructions for charging the tablet using a power adapter or docking station.

Tablet Screen Layout

Describes the on-screen buttons and their functions on the tablet.

Adjusting Screen Brightness

How to adjust the screen brightness automatically or manually.

Changing Tablet Language

Steps to change the tablet's system language.

Setting Up Network Connection

Guide to connecting the tablet to a wireless network.

Getting Started

Registration and Activation

Steps for initial tool activation, including registration and VCI activation.

Home Screen Functions

Key Immobilizer (IMMO)

Function to perform anti-theft key matching and authorize remote control keys.

Immobilizer Programming (IMMO PROG)

Operation requiring X-PROG 3 for programming immobilizer functions.

Key Programmer Module

Module for identifying key chips and generating key models and remote devices.

Vehicle Connections

Connection Preparation

Steps to prepare for connecting the diagnostic tool to the vehicle.

Vehicle Connection Procedure

Instructions for connecting the VCI device to the vehicle's DLC port.

Key Immobilizer & Programming

Key Immobilizer (IMMO)

Function to perform anti-theft key matching and authorize remote control keys.

Immobilizer Programming (IMMO PROG)

Operation requiring X-PROG 3 for programming immobilizer functions.

Key Programmer Module

Module for identifying key chips and generating key models and remote devices.

Diagnosis Operations

Intelligent Diagnose

Automatically identifies VIN and retrieves vehicle information for diagnostics.

Local Diagnose

Manually diagnose a vehicle by selecting the model and software.

Health Report (Quick Test)

Quickly accesses ECU information and generates a detailed vehicle health report.

System Scan

Scans installed vehicle systems to identify available ECUs.

System Selection

Manually select specific vehicle systems for diagnostic testing.

Read Data Stream

Retrieves and displays live data and parameters from the vehicle's ECU.

Actuation Test

Performs vehicle-specific subsystem and component tests by driving actuators.

ADAS Calibration

Calibrates camera-based and radar-based driver assistance systems.

Remote Diagnose System

SmartLink Super Remote Diagnostics

System for remote diagnosis and service between technicians and repair shops.

X431 Remote Diagnostics

Enables instant messaging and remote diagnosis for faster repair jobs.

Service (Reset) Function

Software Update

Update Diagnostic Software & APP

Instructions to update the diagnostic software and mobile applications.

Update IMMO&IMMO PROG Software

Steps to update specific IMMO and IMMO PROG software modules.

Renew Subscription

Information on how to renew the software subscription.

ADAS (Calibration) Module

TPMS Functions

Other Modules and Apps

Common Apps

Common applications like Vehicle Coverage and User Info.

Toolbox Add-ons

Add-on modules to extend diagnostic tool functionality with hardware and apps.

Built-in Apps

Integrates Android system apps for quick access and dialling.

Tablet System Settings

Allows configuration of Android system settings on the tablet.

TeamViewer Remote Support

Enables remote support from technicians via TeamViewer.

Wireless Upgrade Function

Allows Over-the-Air (OTA) updates for the operating system and software.

File Explorer Utility

Features an app and file manager, task killer, and download manager.

J2534 Reprogramming Using SmartLink C

Frequently Asked Questions (FAQ)

About X-431 IMMO PAD

Frequently asked questions regarding power saving, communication errors, and app downloads.

About SmartLink Diag.

Information on network requirements, delay indicators, and vehicle compatibility for SmartLink Diag.

Warranty and Customer Service

Product Warranty Information

Limited warranty terms and conditions for LAUNCH products.

Order Information

Details required for ordering replaceable and optional parts.

Customer Service Contact

Contact information for customer support and technical assistance.