Lenze E84DGFCA Series - Index

Lenze · Decentralised frequency inverter 8400 motec (AS-Interface option) · EDS84DMOTASI EN 5.0 - 02/2019 71
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
A
Accessing process data 40
Active address (C13200) 62
Acyclic parameter data channel 18
Addressing the AS-i slaves 27
All words to the basic device (C13852) 67
All words to the basic device (C13853) 67
Application as directed 12
Application notes (representation) 9
Approvals 17
AS-i
monitoring times (C13208)
64
AS-i bus transaction counter (C13210) 64
AS-i concept of the Communication Unit 34
AS-i connection 23
AS-i error messages
Causes and remedies
57
AS-i error messages (short overview) 56
AS-i profile 7.A.5 35
AS-i profile 7.A.7 37
B
Baud rate 17
Before initial switch-on 25
Broadcast call of the master 30
Bus access method 30
Bus status (C13211) 65
Bus termination 17
C
C01501 | Resp. to communication error with MCI 61
C01503 | MCI timeout 61
C13200 | Active address 62
C13202 | Slave address EPM value 62
C13204 | Override Slave Addresses 63
C13205 | Override of slave addresses during initialisation 63
C13206 | Slave profiles 63
C13207 | Response in case of communication fault 64
C13208 | AS-i
monitoring times
64
C13210 | AS-i bus transaction counter 64
C13211 | Bus status 65
C13213 | CTT2 block parameter transfer
Write parameter block configuration
65
C13214 | CTT2 block parameter transfer
Read parameter block configuration
66
C13220 | Display
Last data to master
66
C13221 | Display
Last data from master
67
C13852 | All words to the basic device 67
C13853 | All words to the basic device 67
C13900 | Firmware product type 68
C13901 | Firmware compilation date 68
C13902 | Firmware version 68
C13950 | Module internal communication status 68
Cable length 17
Codes 61
Commissioning 25
Communication medium 17
Communication profile 17
Communication time 19
Communication-relevant parameters of the operating system
61
Configuration of the master 26
Conformities 17
Connections 15
Conventions 7
Conventions used 7
CTT2
Acyclic device error codes
53
Block parameter transfer read mode 49
Block parameter transfer write mode 51
Read code 47
Read parameter value 45
Standard error codes 52
Write code 48
Write parameter value 46
CTT2 block parameter transfer
Read parameter block configuration (C13214)
66
Write parameter block configuration (C13213) 65
Cycle 32
Cycle time 17, 32
Cyclic parameter data channel 18
D
Data transfer 30
Data transmission slave 1 (AS-i profile 7.A.5) 35
Data transmission slave 2 (AS-i profile 7.A.7) 37
Device and application-specific safety instructions 11
Device profiles 18, 34
Device protection 11
Diagnostics 54
Diagnostics via parameter ports (parameter echo) 38
Diagnostics with the »Engineer« 55
Digital inputs, available 17
Display
Last data to master (C13220)
66
Document history 6
Drive offline (error message) 57
Drive parameter access failure - channel 1 (error message) 57
Drive parameter access failure - channel 2 (error message) 57
Drive PDO communication timeout (error message) 58
E
Electrical installation 22
E-mail to Lenze 74
Error messages 56
Index